Refer to DTC P244B00.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P244B00
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P246300 | Particulate Filter Restriction - Soot Accumulation Bank 1 | During high load operation, the PM (Particulate Matter) accumulation ratio is 100% or higher for 1 second or more (1 trip detection logic). | Front exhaust pipe assembly (GPF) | Comes on*/-
*: The MIL is illuminated when PM accumulation has progressed and protection of parts has become necessary. |
DTC stored | SAE Code:
P2463 |
When the accumulation ratio of the PM in the GPF (Gasoline Particulate Filter) is at the specified value or higher, output is limited during high load operation to prevent the GPF from rising to a high temperature. A DTC is stored at this time.
The MIL is illuminated when PM accumulation has progressed and protection of parts has become necessary.
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine and wait 10 seconds or more.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P246300.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
Enter the following menus: Powertrain / Engine / Data List / PM Deposition Ratio Bank1.
Read the value displayed on the GTS.
If the PM Depensition Ratio value is less than 100%, the system is normal.
If the PM Depensition Ratio value is 100% or higher, perform forced particulate filter rejuvenation.
Refer to DTC P0245211.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P245211
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Clear the Vehicle Control History after completing repairs.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>VEHICLE CONTROL HISTORY
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Ash Deposition Ratio Bank1.
| Tester Display |
|---|
| Ash Deposition Ratio Bank1 |
Read the value displayed on the GTS.
| GTS Display | Specified Condition |
|---|---|
| Ash Deposition Ratio Bank1 | Less than 100% |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB) / Clear.
By performing this procedure, all stored Vehicle Control History items will be cleared.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Clear the Vehicle Control History.
| Proceed to |
|---|
| NEXT |
NEXT
Perform the PM Rejuvenate Mode.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>PARTICULATE FILTER REJUVENATE PROCEDURE
| Proceed to |
|---|
| NEXT |
NEXT
Replace the front exhaust pipe assembly (GPF).
| Proceed to |
|---|
| NEXT |
Clear the GPF deterioration record using the GTS after replacing the front exhaust pipe assembly.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB) / Clear.
By performing this procedure, all stored Vehicle Control History items will be cleared.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Clear the Vehicle Control History.
| Proceed to |
|---|
| NEXT |
NEXT