Home › Brake › BRAKE (REAR) › REAR BRAKE (for TMMT Made) › from 2018.05
RM32H0E _54 Brake _060042 BRAKE (REAR) _0358313 REAR BRAKE(for TMMT Made) A

BRAKE (REAR)  REAR BRAKE(for TMMT Made)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 2.REMOVE REAR WHEEL

Hide 3.PERFORM REAR BRAKE PAD REPLACEMENT MODE

Hide 4.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 47319F 5.SEPARATE REAR FLEXIBLE HOSE

a.
C399537

Remove the union bolt and gasket, and disconnect the rear flexible hose from the rear disc brake cylinder assembly.


Hide 890C0A 6.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.
C399528

Disconnect the No. 2 parking brake wire assembly from the parking brake actuator assembly.

NOTICE:
·

Remove any dirt or foreign matter on and around the connector before performing this work.

·

Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.




Hide 46310B 7.REMOVE PARKING BRAKE ACTUATOR ASSEMBLY

a.
C399538

Using a 5 mm hexagon socket wrench, remove the 2 bolts and parking brake actuator assembly from the rear disc brake cylinder assembly.

NOTICE:
·

Check that there are no brake fluid leaks from the back of the rear disc brake cylinder assembly.

·

If there are any brake fluid leaks, replace the rear disc brake cylinder assembly.




b.

Remove the O-ring from the rear disc brake cylinder assembly.


Hide 8.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C399539C01
1.927,2.594 2.156,2.781 0.229,0.188 10 true *a 1.146,2.688 1.365,2.885 0.219,0.198 10 false *b
*a Turn
*b Hold


Hold the 2 rear disc brake cylinder slide pins and remove the 2 bolts and rear disc brake cylinder assembly.


Hide 9.REMOVE REAR DISC BRAKE PAD

a.
C399540

Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.


Hide 10.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

Hide 11.REMOVE REAR DISC BRAKE PAD SUPPORT PLATE

a.
C399541

Remove the 4 rear disc brake pad support plates from the rear disc brake cylinder mounting.

NOTICE:

Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.



Hide 12.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C399542C01
2.583,1.667 2.458,1.417 true 2.313,0.531 2.188,0.281 true 2.583,1.708 2.833,1.917 0.25,0.208 10 true *1 2.323,0.583 2.521,0.823 0.198,0.24 10 true *2
*1 Rear No. 1 Disc Brake Cylinder Slide Pin
*2 Rear No. 2 Disc Brake Cylinder Slide Pin


Remove the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin from the rear disc brake cylinder mounting.


b.
C399543C01
2.073,1.25 2.49,0.833 false 2.542,0.719 2.854,0.875 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the rear disc brake cylinder slide bushing from the rear No. 1 disc brake cylinder slide pin.

NOTICE:

Do not damage the rear No. 1 disc brake cylinder slide pin.



Hide 13.REMOVE REAR DISC BRAKE BUSHING DUST BOOT

a.
C399544

Remove the 2 rear disc brake bushing dust boots from the rear disc brake cylinder mounting.


Hide 14.REMOVE REAR DISC BRAKE CYLINDER MOUNTING

a.
C399545

Remove the 2 bolts and rear disc brake cylinder mounting from the rear axle carrier sub-assembly.


Hide 42431 15.REMOVE REAR DISC

a.
C366010C01
0.99,1.927 1.51,1.5 true 0.979,1.927 1.49,1.448 true 0.823,1.854 1.135,2.01 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the rear disc and rear axle hub and bearing assembly.


b.

Remove the rear disc from the rear axle hub and bearing assembly.