Refer to DTC P019011.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P019011
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P019015 | Fuel Rail Pressure Sensor "A" Circuit Short to Battery or Open | The fuel pressure sensor output voltage is higher than 4.9 V for 3 seconds or more (1 trip detection logic). | ·
Open or short in fuel pressure sensor circuit ·
Fuel delivery pipe (Fuel pressure sensor) ·
ECM |
Comes on | DTC stored | SAE Code:
P0193 |
When this DTC is output, check the fuel pressure (for high pressure side) in the Data List. Enter the following menus: Powertrain / Engine / Data List / All Data / High Fuel Pressure Sensor.
| DTC No. | High Fuel Pressure Sensor | Malfunction |
|---|---|---|
| P019015 | Approximately 33000 kPag or higher | ·
Short in VCPR to PR circuit ·
Open in PR circuit ·
Open in EPR circuit |
If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.
This DTC is stored if the fuel pressure sensor output voltage is out of the standard range due to an open or short in the sensor circuit.
Example:
If the fuel pressure sensor output voltage is higher than 4.9 V for 3 seconds or more, the ECM store this DTC.
| Required Sensors/Components | Fuel delivery pipe (fuel pressure sensor) |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Idle the engine for 10 seconds.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P019015.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Refer to DTC P019011.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P019011
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Disconnect the C54 fuel pressure sensor connector.
Disconnect the C62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C54-3 (PR) - C62-103 (PR) | Always | Below 1 Ω |
| C54-2 (E2) - C62-135 (EPR) | Always | Below 1 Ω |
| C54-3 (PR) or C62-103 (PR) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Fuel Pressure Sensor) |
Disconnect the fuel pressure sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C54-1 (VC) - C54-2 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG