These DTCs are stored when a malfunction occurs in the telephone antenna assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C0 | GPS Antenna Disconnected (Short) | Navigation antenna error | ·
Navigation ECU ·
Roof Antenna Assembly ·
Antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly ·
No. 3 antenna cord sub-assembly ·
Antenna divider*1 |
| B15C1 | GPS Antenna Disconnected (Open) | Error of the power source to the navigation antenna | ·
Navigation ECU ·
Roof Antenna Assembly ·
Antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly ·
No. 3 antenna cord sub-assembly ·
Antenna divider*1 |
*1: w/ Manual (SOS) Switch
Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the No. 3 antenna cord sub-assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL
| *a | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Telephone Antenna Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D-2 - RA-5 | Always | Below 1 Ω |
| D-2a - RA-5a | Always | Below 1 Ω |
| D-2 or RA-5 - Body ground | Always | 10 kΩ or higher |
| D-2a or RA-5a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 2 antenna cord sub-assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL
| *a | Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C-2 - B-2 | Always | Below 1 Ω |
| C-2a - B-2a | Always | Below 1 Ω |
| C-2 or B-2 - Body ground | Always | 10 kΩ or higher |
| C-2a or B-2a - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (w/ Manual (SOS) switch) | A |
| OK (w/o Manual (SOS) switch) | B |
| NG | C |
A
B
C
Remove the antenna cord sub-assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL
| *a | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Antenna Divider) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-2 - AD-6 | Always | Below 1 Ω |
| A-2a - AD-6a | Always | Below 1 Ω |
| A-2 or AD-6 - Body ground | Always | 10 kΩ or higher |
| A-2a or AD-6a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Antenna Divider) |
Remove the antenna divider.
Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6 - 5 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the antenna cord sub-assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL
| *a | Front view of wire harness connector
(to Antenna Divider) |
| *b | Front view of wire harness connector
(to Navigation ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AD-5 - GB-1 (GPS) | Always | Below 1 Ω |
| AD-5a - GB-1a | Always | Below 1 Ω |
| AD-5 or GB-1 (GPS) - Body ground | Always | 10 kΩ or higher |
| AD-5 or GB-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the antenna cord sub-assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL
| *a | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Navigation ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-2 - GB-1 (GPS) | Always | Below 1 Ω |
| A-2a - GB-1a | Always | Below 1 Ω |
| A-2 or GB-1 (GPS) - Body ground | Always | 10 kΩ or higher |
| A-2a or GB-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the roof antenna assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG