Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION ECU › 2019.09–2020.08
RM32H0E _56 Audio / Visual / Telematics _060815 NAVIGATION / MULTI INFO DISPLAY _0298316 NAVIGATION ECU A

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION ECU  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the navigation ECU removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 55470 3.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

Hide 67914 4.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 5.REMOVE COWL SIDE TRIM BOARD LH

Hide 55606 6.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55434B 7.REMOVE INSTRUMENT PANEL LOWER CENTER FINISH PANEL

Hide 55440D 8.REMOVE INSTRUMENT PANEL BOX ASSEMBLY

Hide 55406B 9.REMOVE INSTRUMENT CLUSTER FINISH LOWER CENTER PANEL SUB-ASSEMBLY

Hide 86841 10.REMOVE NAVIGATION ECU WITH BRACKET (for TMMT Made)

a.
E426201

Disconnect the 3 connectors.


b.

Remove the 2 nuts.


c.

Pull out and remove the navigation ECU with bracket.


Hide 86841 11.REMOVE NAVIGATION ECU WITH BRACKET (for TMC Made)

a.
E426302

Disconnect the 3 connectors.


b.

Remove the 2 nuts.


c.
E426303

Pull out and remove the navigation ECU with bracket.


d.

Disconnect the connector.


Hide 86101M 12.REMOVE ANTENNA CORD SUB-ASSEMBLY (for TMC Made)

a.
E426485

Disconnect the 2 connectors.


b.
E426304

Disengage the clamps to remove the antenna cord sub-assembly.


Hide 86844A 13.REMOVE NO. 1 NAVIGATION ECU BRACKET (for TMMT Made)

E426202

a.

Remove the 2 bolts.


b.

Disengage the guide to remove the No. 1 navigation ECU bracket from the navigation ECU.


Hide 86844A 14.REMOVE NO. 2 NAVIGATION ECU BRACKET (for TMMT Made)

a.
E426203

Remove the 2 bolts.


b.

Disengage the guide to remove the No. 2 navigation ECU bracket from the navigation ECU.


Hide 86457 15.REMOVE NO. 1 MULTI-MEDIA MODULE BRACKET (for TMC Made)

a.
E426306

Remove the 2 bolts.


b.

Disengage the guides to remove the No. 1 multi-media module bracket from the navigation ECU.


Hide 86457A 16.REMOVE NO. 2 MULTI-MEDIA MODULE BRACKET (for TMC Made)

E426305

a.

Remove the 2 bolts.


b.

Disengage the guides to remove the No. 2 multi-media module bracket from the navigation ECU.