Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › from 2019.09
RM32H0E _58 Vehicle Interior _059856 INTERIOR PANELS / TRIM _0293790 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 55357B 1.INSTALL NO. 3 INSTRUMENT PANEL CUSHION (w/ Cushion)

a.
B557968C01
2.323,1 2.656,1 true 2.677,0.896 2.906,1.063 0.229,0.167 10 true *a
*a Marking


Align a new No. 3 instrument panel cushion with the markings on the instrument panel safety pad sub-assembly and install it as shown in the illustration.

HINT:

Peel off the backing paper from the double-sided tape before installing the No. 3 instrument panel cushion.



Hide 55356C 2.INSTALL NO. 2 INSTRUMENT PANEL CUSHION (w/ Cushion)

a.
B557966C01
0.688,1 1.021,1 true 0.385,0.896 0.625,1.083 0.24,0.188 10 true *a
*a Marking


Align a new No. 2 instrument panel cushion with the markings on the instrument panel safety pad sub-assembly and install it as shown in the illustration.

HINT:

Peel off the backing paper from the double-sided tape before installing the No. 2 instrument panel cushion.



Hide 55355 3.INSTALL NO. 1 INSTRUMENT PANEL CUSHION

a.
B459269C01
1.667,0.729 1.896,0.292 false 1.323,0.896 1.479,0.875 false 0.427,1.635 0.635,1.438 false 2.781,1.583 3.042,1.375 true 1.135,0.76 1.448,0.917 0.313,0.156 10 false *a 0.26,1.573 0.573,1.729 0.313,0.156 10 false *b 1.917,0.188 2.229,0.344 0.313,0.156 10 false *c 1.302,0.188 1.615,0.344 0.313,0.156 10 false A 0.479,1.135 0.792,1.292 0.313,0.156 10 false B 2.667,1.833 2.833,2.01 0.167,0.177 10 true C 3.063,1.25 3.26,1.438 0.198,0.188 10 false *c
*a Instrument Panel Front Side End
*b Instrument Panel Left Side End
*c Marking


Install a new No. 1 instrument panel cushion as shown in the illustration.

Standard Measurement:
Area Measurement
A 3.0 mm (0.118 in.)
B 0 mm (0 in.)
C 2.0 mm (0.0787 in.)


HINT:

Peel off the backing paper from the double-sided tape before installing the No. 1 instrument panel cushion.



Hide 55328 4.INSTALL NO. 1 INSTRUMENT PANEL PIN

HINT:

Use the same procedure as for the opposite side.


a.
B459267

Engage the guide to install the No. 1 instrument panel pin.


b.

Install the screw <D>.


Hide 82142 5.INSTALL NO. 2 INSTRUMENT PANEL WIRE

a.
B514919C01
0.083,0.146 0.333,0.333 0.25,0.188 12 true *A 0.083,2.49 0.323,2.677 0.24,0.188 12 true *B
*A for LHD
*B for RHD


w/ Ion Generator:

i.

Engage the clamps to install the No. 2 instrument panel wire.



b.
B514920C01
0.104,0.167 0.323,0.344 0.219,0.177 12 true *A 0.083,2.469 0.302,2.656 0.219,0.188 12 true *B
*A for LHD
*B for RHD


w/o Ion Generator:

i.

Engage the clamps to install the No. 2 instrument panel wire.



Hide 89120A 6.INSTALL AUTOMATIC LIGHT CONTROL SENSOR

Hide 88051A 8.INSTALL ION GENERATOR SUB-ASSEMBLY (w/ Ion Generator)

Hide 73960A 9.INSTALL INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

Hide 55660 10.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B459264

Engage the guides to install the No. 2 instrument panel register assembly.


b.

Install the 3 screws <D>.


Hide 55650 11.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B459263

Engage the guides to install the No. 1 instrument panel register assembly.


b.

Install the 4 screws <D>.


Hide 55086 12.INSTALL NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
B461419

w/ Ion Generator:

i.

Connect the rear air duct sub-assembly.



b.
B513006

Engage the guides to install the No. 3 heater to register duct sub-assembly.


c.

Install the 3 screws <D>.


Hide 55084E 13.INSTALL NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
B459261C03
0.25,0.927 0.365,0.708 true 1.177,0.542 1.396,0.469 true 2.146,0.906 2.458,0.781 true 2.135,1.969 2.365,1.833 true 2.979,1.781 3.188,1.625 true 2.469,0.688 2.677,0.875 0.208,0.188 10 true *a 0.167,0.938 0.375,1.115 0.208,0.177 10 true *b 1.406,0.385 1.615,0.563 0.208,0.177 10 true *b 2.365,1.74 2.563,1.896 0.198,0.156 10 true *b 3.198,1.542 3.396,1.698 0.198,0.156 10 true *b
*a Clamp
*b Guide


Engage the guides to install the No. 1 heater to register duct sub-assembly.


b.

Install the 3 screws <D>.


c.

Engage the clamp to connect the No. 2 instrument panel wire.


Hide 55950G 14.INSTALL DEFROSTER NOZZLE ASSEMBLY

a.

w/ Antenna Divider:

i.

Connect the connector.



b.
B459260

Engage the guides to install the defroster nozzle assembly.


c.

Install the 3 screws <D>.


Hide 55962 15.INSTALL NO. 2 SIDE DEFROSTER NOZZLE

a.
B459259

Engage the claws to install the No. 2 side defroster nozzle.


Hide 55961 16.INSTALL NO. 1 SIDE DEFROSTER NOZZLE

a.
B459258

Engage the claws to install the No. 1 side defroster nozzle.