Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2019.09
RM32H0E _56 Audio / Visual / Telematics _060815 NAVIGATION / MULTI INFO DISPLAY _0299845 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  AVC-LAN Circuit  


DESCRIPTION

Each unit of the audio and visual system connected to the AVC-LAN (communication bus) transmits signals via AVC-LAN communication.

If a short to +B or short to ground occurs in an AVC-LAN communication line, the audio and visual system will not function normally because communication is not possible.

WIRING DIAGRAM

E425796E03
2.958,2.208 4.938,2.396 1.979,0.188 10 false : AVC-LAN Communication Line 1.01,1.469 1.469,1.667 0.458,0.198 10 false F152 5.094,0.583 5.552,0.781 0.458,0.198 10 false TX1+ 5.052,1.615 6.26,2.063 1.208,0.448 10 false Radio and Display Receiver Assembly 0.99,1.625 2.198,2.198 1.208,0.573 10 false Stereo Component Amplifier Assembly 5.052,1.469 5.51,1.667 0.458,0.198 10 false F129 5.104,0.979 5.563,1.177 0.458,0.198 10 false TX1- 4.906,0.438 5.104,0.615 0.198,0.177 10 false 5 4.896,0.833 5.094,1.01 0.198,0.177 10 false 6 1.844,0.573 2.302,0.771 0.458,0.198 10 false TX+ 1.875,0.948 2.115,1.156 0.24,0.208 10 false TX- 2.177,0.448 2.375,0.625 0.198,0.177 10 false 8 2.177,0.833 2.375,1.01 0.198,0.177 10 false 7

CAUTION / NOTICE / HINT

HINT:

The radio and display receiver assembly is the master unit.


PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Remove the radio and display receiver assembly.


b.
E394515C20
1.583,0.813 1.99,1.031 0.406,0.219 2.271,2.417 2.635,1.813 true 2.823,2.417 2.771,1.813 true 1.635,0.854 2.125,1.208 0.49,0.354 10 false F129 2.198,2.448 2.604,2.698 0.406,0.25 10 false TX1- 2.792,2.448 3.167,2.667 0.375,0.219 10 false TX1+ 0.188,0.167 0.5,0.365 0.313,0.198 10 false *a
*a Component without harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F129-5 (TX1+) - F129-6 (TX1-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the F129 radio and display receiver assembly connector.


b.

Disconnect the F152 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F152-8 (TX+) - F129-5 (TX1+) Always Below 1 Ω
F152-7 (TX-) - F129-6 (TX1-) Always Below 1 Ω
F152-8 (TX+) or F129-5 (TX1+) - Body ground Always 10 kΩ or higher
F152-7 (TX-) or F129-6 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal.



Result:
Proceed to
OK
NG



OK

REPLACE MALFUNCTIONING PARTS

NG