This DTC is stored if the radio and display receiver assembly judges that the signals or signal lines between the radio and display receiver assembly and the rear television camera assembly are not normal as a result of its self check.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1622 | Back Camera Disconnected | Open or short in the rear television camera assembly signal circuit | ·
Harness or connector ·
Rear television camera assembly ·
Radio and display receiver assembly |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
Disconnect the F131 radio and display receiver assembly connector.
Disconnect the S11 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F131-30 (CA+) - S11-6 (CB+) | Always | Below 1 Ω |
| F131-28 (V+) - S11-3 (CV+) | Always | Below 1 Ω |
| F131-29 (V-) - S11-2 (CV-) | Always | Below 1 Ω |
| F131-27 (CGND) - S11-5 (CGND) | Always | Below 1 Ω |
| F131-26 (CSLD) - Body ground | Always | Below 1 Ω |
| F131-30 (CA+) or S11-6 (CB+) - Body ground | Always | 10 kΩ or higher |
| F131-28 (V+) or S11-3 (CV+) - Body ground | Always | 10 kΩ or higher |
| F131-29 (V-) or S11-2 (CV-) - Body ground | Always | 10 kΩ or higher |
| F131-27 (CGND) or S11-5 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the F131 radio and display receiver assembly connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F131-29 (V-) - Body ground | Always | Below 1 Ω |
| F131-27 (CGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F131-30 (CA+) - F131-27 (CGND) | Ignition switch ACC | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio Receiver Type)>REMOVAL
Reconnect the S11 rear television camera assembly connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
| *a | Waveform 1 (camera lens is not covered, displaying an image) |
| *b | Waveform 2 (camera lens is covered, blacking out the screen) |
| *c | Synchronization Signal |
| *d | Video Waveform |
Using an oscilloscope, check the waveform of the rear television camera assembly.
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.
Waveform is similar to that shown in the illustration.
| Item | Content |
|---|---|
| Measurement terminal | F131-28 (V+) - F131-29 (V-) |
| Measurement setting | 200 mV/DIV., 50 μs./DIV. |
| Condition | Ignition switch ON, shift lever in R |
The video waveform changes according to the image sent by the rear television camera assembly.
The video waveform is constantly output when the ignition switch ACC.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio Receiver Type)>REMOVAL
NG