DTC C1622 is stored if the parking assist ECU judges as a result of its self check that the signals or signal lines between the parking assist ECU and the rear television camera assembly are not normal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1622 | Open or Short Circuit in Back Camera Signal | Open or short in the rear television camera signal circuit | ·
Harness or connector ·
Rear television camera assembly ·
Parking assist ECU |
When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION
Disconnect the S11 rear television camera assembly connector.
Disconnect the M116 parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S11-6 (CB+) - M116-8 (CB+) | Always | Below 1 Ω |
| S11-3 (CV+) - M116-11 (CV+) | Always | Below 1 Ω |
| S11-2 (CV-) - M116-35 (CV-) | Always | Below 1 Ω |
| S11-5 (CGND) - M116-25 (CGND) | Always | Below 1 Ω |
| M116-12 (SGND) - Body ground | Always | 10 kΩ or higher |
| S11-6 (CB+) or M116-8 (CB+) - Body ground | Always | 10 kΩ or higher |
| S11-3 (CV+) or M116-11 (CV+) - Body ground | Always | 10 kΩ or higher |
| S11-2 (CV-) or M116-35 (CV-) - Body ground | Always | 10 kΩ or higher |
| S11-5 (CGND) or M116-25 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M116 parking assist ECU connector.
| *a | Component without harness connected
(Parking Assist ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M116-35 (CV-) - Body ground | Always | Below 1 Ω |
| M116-25 (CGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Remove the parking assist ECU with the connector still connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M116-25 (CGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M116-8 (CB+) - M116-25 (CGND) | Engine switch on (IG) | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
| *a | Component with harness connected
(Parking Assist ECU) |
Using an oscilloscope, check the waveform of the rear television camera assembly.
| *a | Waveform 1 (camera lens not covered, displaying an image) |
| *b | Waveform 2 (camera lens covered, blacking out the screen) |
| *c | Synchronization Signal |
| *d | Video Waveform |
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
The video waveform changes according to the image sent by the rear television camera assembly.
The video waveform is constantly output when the engine switch is on (ACC).
| Item | Content |
|---|---|
| Terminal No. (Symbol) | M116-11 (CV+) - M116-25 (CGND) |
| Tool Setting | 200 mV/DIV., 50 μs./DIV. |
| Condition | Engine switch on (IG), panoramic view monitor system operating |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG