Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2019.09
RM32H0E _56 Audio / Visual / Telematics _060571 PARK ASSIST / MONITORING _0404351 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1681  Front Camera Feedback Malfunction  


DESCRIPTION

DTC C1681 is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the front television camera assembly to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1681 Front Camera Feedback Malfunction Front television camera power supply failure
·

Harness or connector

·

Front television camera assembly

·

Parking assist ECU



WIRING DIAGRAM

E372776E17
1.74,0.615 2.656,0.813 0.917,0.198 10 false BCB+ 1.771,0.99 2.688,1.188 0.917,0.198 10 false BCV- 1.74,1.406 2.656,1.604 0.917,0.198 10 false BCV+ 1.729,1.813 2.646,2.01 0.917,0.198 10 false BGND 0.583,2.615 1.5,2.813 0.917,0.198 10 false B17 0.583,2.813 3.354,3.104 2.771,0.292 10 false Front Television Camera Assembly 3.521,2 3.896,2.219 0.375,0.219 10 false * 2.219,0.49 2.594,0.708 0.375,0.219 10 false 6 2.219,0.885 2.594,1.104 0.375,0.219 10 false 2 2.208,1.271 2.583,1.49 0.375,0.219 10 false 3 2.208,1.677 2.583,1.896 0.375,0.219 10 false 5 4.833,0.5 5.208,0.719 0.375,0.219 10 false 7 4.76,0.906 5.135,1.125 0.375,0.219 10 false 10 4.76,1.313 5.135,1.531 0.375,0.219 10 false 33 4.76,1.698 5.135,1.917 0.375,0.219 10 false 24 4.76,2.094 5.135,2.313 0.375,0.219 10 false 34 4.938,2.646 5.542,2.865 0.604,0.219 10 false M116 4.938,2.833 6.844,3.458 1.906,0.625 10 false Parking Assist ECU 5.021,0.615 5.938,0.813 0.917,0.198 10 false BCB+ 5.021,1.01 5.938,1.208 0.917,0.198 10 false BCV- 5.01,1.406 5.927,1.604 0.917,0.198 10 false BCV+ 5.01,1.802 5.927,2 0.917,0.198 10 false BGND 5.01,2.208 5.927,2.406 0.917,0.198 10 false SGND 3.792,3.292 4.708,3.49 0.917,0.198 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the M116 parking assist ECU connector.


b.

Disconnect the B17 front television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M116-7 (BCB+) - B17-6 (BCB+) Always Below 1 Ω
M116-33 (BCV+) - B17-3 (BCV+) Always Below 1 Ω
M116-10 (BCV-) - B17-2 (BCV-) Always Below 1 Ω
M116-24 (BGND) - B17-5 (BGND) Always Below 1 Ω
M116-34 (SGND) - Body ground Always 10 kΩ or higher
M116-7 (BCB+) or B17-6 (BCB+) - Body ground Always 10 kΩ or higher
M116-33 (BCV+) or B17-3 (BCV+) - Body ground Always 10 kΩ or higher
M116-10 (BCV-) or B17-2 (BCV-) - Body ground Always 10 kΩ or higher
M116-24 (BGND) or B17-5 (BGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK PARKING ASSIST ECU (BCV-, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (BCV-, BGND)
a.

Disconnect the M116 parking assist ECU connector.


b.
E430245C02
1.469,0.219 1.875,0.458 0.406,0.24 2.052,1.146 2.333,1.688 true 1.104,0.406 1.396,0.979 true 1.51,0.271 2.021,0.677 0.51,0.406 10 false M116 0.115,0.063 0.313,0.24 0.198,0.177 10 false *a 2.354,1.729 2.771,1.885 0.417,0.156 10 false BGND 0.729,0.271 1.146,0.427 0.417,0.156 10 false BCV-
*a Component without harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M116-24 (BGND) - Body ground Always Below 1 Ω
M116-10 (BCV-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU (BCB+, BGND)

NG

3.CHECK PARKING ASSIST ECU (BCB+, BGND)
a.
E403271C63
1.604,0.688 2.042,0.906 0.438,0.219 1.646,1.656 1.354,2.427 true 2.646,2.417 2.354,1.646 true 0.167,0.156 0.385,0.333 0.219,0.177 10 false *a 1.146,2.49 1.573,2.656 0.427,0.167 10 false BCB+ 2.583,2.49 3,2.656 0.417,0.167 10 false BGND 1.656,0.719 2.313,1.104 0.656,0.385 10 false M116
*a Component with harness connected
(Parking Assist ECU)


Remove the parking assist ECU with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M116-24 (BGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M116-7 (BCB+) - M116-24 (BGND) Engine switch on (IG) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)

NG

4.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)
a.

Remove the parking assist ECU with the connector still connected.


b.
E403271C64
1.604,0.688 2.042,0.906 0.438,0.219 1.646,1.656 1.354,2.427 true 2.646,2.448 2.354,1.656 true 0.167,0.156 0.385,0.333 0.219,0.177 10 false *a 1.146,2.49 1.573,2.656 0.427,0.167 10 false BCV+ 2.708,2.469 3.125,2.635 0.417,0.167 10 false BGND 1.656,0.719 2.333,1.073 0.677,0.354 10 false M116
*a Component with harness connected
(Parking Assist ECU)


Using an oscilloscope, check the waveform of the front television camera assembly.

HINT:
E265840C28
0.854,1.99 1.115,1.583 true 1.458,1.979 1.24,1.469 true 1.51,4.125 1.281,3.542 true 0.854,4.146 1.146,3.604 true 0.229,0.229 0.542,0.427 0.313,0.198 10 false *a 0.396,1.052 0.76,1.313 0.365,0.26 10 false GND 0.396,3.208 0.76,3.469 0.365,0.26 10 false GND 0.26,2.271 0.625,2.531 0.365,0.26 10 false *b 0.646,4.073 1.01,4.333 0.365,0.26 10 false *c 0.677,1.958 1.042,2.219 0.365,0.26 10 false *c 1.458,1.969 1.823,2.229 0.365,0.26 10 false *d 1.479,4.115 1.844,4.375 0.365,0.26 10 false *d
*a Waveform 1 (camera lens not covered, displaying an image)
*b Waveform 2 (camera lens covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


·

A waterproof connector is used for the front television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.

·

The video waveform changes according to the image sent by the front television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).



Measurement Condition
Item Content
Terminal No. (Symbol) M116-33 (BCV+) - M116-24 (BGND)
Tool Setting 200 mV/DIV., 50 μs./DIV.
Condition Engine switch on (IG), panoramic view monitor system operating

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG