Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2019.09
RM32H0E _56 Audio / Visual / Telematics _060571 PARK ASSIST / MONITORING _0404351 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1683  Side Camera Feedback Malfunction  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the passenger side television camera assembly to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1683 Side Camera Feedback Malfunction Side camera feedback malfunction
·

Harness or connector

·

Parking assist ECU

·

Side television camera assembly LH

·

Outer rear view mirror assembly with cover LH



WIRING DIAGRAM

E419943E12
0.313,2.583 1.771,3.146 1.458,0.563 10 false Side Television Camera Assembly LH 3.469,0.656 4.385,0.854 0.917,0.198 10 false LCB+ 3.5,1.438 4.417,1.635 0.917,0.198 10 false LCV- 3.469,1.052 4.385,1.25 0.917,0.198 10 false LCV+ 3.438,1.844 4.354,2.042 0.917,0.198 10 false LGND 5.729,0.646 6.646,0.844 0.917,0.198 10 false LCB+ 5.729,1.469 6.646,1.667 0.917,0.198 10 false LCV- 5.729,1.052 6.646,1.25 0.917,0.198 10 false LCV+ 5.729,1.823 6.646,2.021 0.917,0.198 10 false LGND 5.719,2.24 6.635,2.438 0.917,0.198 10 false SGND 4.406,3.24 5.323,3.438 0.917,0.198 10 false *: Shielded 5.531,2.729 7.01,3.271 1.479,0.542 10 false Parking Assist ECU 2.74,2.76 4.229,3.177 1.49,0.417 10 false Outer Rear View Mirror Assembly with Cover LH 2.75,2.604 3.281,2.823 0.531,0.219 10 false J11 5.531,2.563 6.042,2.781 0.51,0.219 10 false M116 4.74,1.979 5.271,2.198 0.531,0.219 10 false * 3.917,0.531 4.448,0.75 0.531,0.219 10 false 5 3.906,0.927 4.438,1.146 0.531,0.219 10 false 6 3.906,1.344 4.438,1.563 0.531,0.219 10 false 13 3.906,1.719 4.438,1.938 0.531,0.219 10 false 12 5.542,0.542 6.073,0.76 0.531,0.219 10 false 9 5.479,0.948 6.01,1.167 0.531,0.219 10 false 36 5.469,1.354 6,1.573 0.531,0.219 10 false 13 5.479,1.719 6.01,1.938 0.531,0.219 10 false 26 5.479,2.115 6.01,2.333 0.531,0.219 10 false 14

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1683 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH)
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH)
a.

Disconnect the M116 parking assist ECU connector.


b.

Disconnect the J11 outer rear view mirror assembly with cover LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M116-9 (LCB+) - J11-5 (LCB+) Always Below 1 Ω
M116-36 (LCV+) - J11-6 (LCV+) Always Below 1 Ω
M116-13 (LCV-) - J11-13 (LCV-) Always Below 1 Ω
M116-26 (LGND) - J11-12 (LGND) Always Below 1 Ω
M116-14 (SGND) - Body ground Always Below 1 Ω
M116-9 (LCB+) or J11-5 (LCB+) - Body ground Always 10 kΩ or higher
M116-36 (LCV+) or J11-6 (LCV+) - Body ground Always 10 kΩ or higher
M116-13 (LCV-) or J11-13 (LCV-) - Body ground Always 10 kΩ or higher
M116-26 (LGND) or J11-12 (LGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU (LCV-, LGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK PARKING ASSIST ECU (LCV-, LGND)
a.

Disconnect the M116 parking assist ECU connector.


b.
E430245C03
1.479,0.219 1.938,0.479 0.458,0.26 1.927,1.146 2.063,1.708 true 0.896,1.781 1.188,1.01 true 1.531,0.271 2.167,0.646 0.635,0.375 10 false M116 0.115,0.063 0.313,0.24 0.198,0.177 10 false *a 1.969,1.74 2.385,1.896 0.417,0.156 10 false LGND 0.677,1.875 1.188,2.052 0.51,0.177 10 false LCV-
*a Component without harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M116-26 (LGND) - Body ground Always Below 1 Ω
M116-13 (LCV-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK PARKING ASSIST ECU (LCB+, LGND)

NG

4.CHECK PARKING ASSIST ECU (LCB+, LGND)
a.
E403271C65
1.698,0.729 2.135,0.969 0.438,0.24 2.198,1.635 2.469,2.354 true 2.406,0.896 2.198,1.458 true 0.167,0.156 0.385,0.333 0.219,0.177 10 false *a 2.458,2.427 2.885,2.594 0.427,0.167 10 false LGND 2.448,0.698 2.865,0.865 0.417,0.167 10 false LCB+ 1.75,0.771 2.354,1.125 0.604,0.354 10 false M116
*a Component with harness connected
(Parking Assist ECU)


Remove the parking assist ECU with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M116-26 (LGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M116-9 (LCB+) - M116-26 (LGND) Engine switch on (IG) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH (LCV+, LGND)

NG

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH (LCV+, LGND)
a.

Remove the parking assist ECU with the connector still connected.


b.
E403271C66
1.698,0.729 2.135,0.969 0.438,0.24 1.188,2.323 1.417,1.563 true 2.188,1.635 2.375,2.427 true 0.167,0.156 0.385,0.333 0.219,0.177 10 false *a 2.302,2.469 2.729,2.635 0.427,0.167 10 false LGND 0.865,2.427 1.281,2.594 0.417,0.167 10 false LCV+ 1.75,0.771 2.281,1.073 0.531,0.302 10 false M116
*a Component with harness connected
(Parking Assist ECU)


Using an oscilloscope, check the waveform of the side television camera assembly LH.

HINT:

A waterproof connector is used for the side television camera assembly LH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


HINT:
E265840C28
0.854,1.99 1.115,1.583 true 1.458,1.979 1.24,1.469 true 1.51,4.125 1.281,3.542 true 0.854,4.146 1.146,3.604 true 0.229,0.229 0.542,0.427 0.313,0.198 10 false *a 0.396,1.052 0.76,1.313 0.365,0.26 10 false GND 0.396,3.208 0.76,3.469 0.365,0.26 10 false GND 0.26,2.271 0.625,2.531 0.365,0.26 10 false *b 0.646,4.073 1.01,4.333 0.365,0.26 10 false *c 0.677,1.958 1.042,2.219 0.365,0.26 10 false *c 1.458,1.969 1.823,2.229 0.365,0.26 10 false *d 1.479,4.115 1.844,4.375 0.365,0.26 10 false *d
*a Waveform 1 (camera lens not covered, displaying an image)
*b Waveform 2 (camera lens covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


·

The video waveform changes according to the image sent by the side television camera assembly LH.

·

The video waveform is constantly output when the engine switch is on (ACC).



Measurement Condition
Item Content
Tester Connection M116-36 (LCV+) - M116-26 (LGND)
Tool Setting 200 mV/DIV., 50 μs./DIV.
Condition Engine switch on (IG), panoramic view monitor system operating

OK:

Waveform is similar to that shown in illustration.



Result:
Proceed to
OK
NG



OK

NG

6.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
6.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Replace the side television camera assembly LH with a new or known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1686 is not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY LH IS DEFECTIVE)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH