This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the driver side television camera assembly to the parking assist ECU.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1686 | Driver Side Camera Video Sync Signal Malfunction | Side camera feedback malfunction | ·
Harness or connector ·
Parking assist ECU ·
Side television camera assembly RH ·
Outer rear view mirror assembly with cover RH |
When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION
Clear the DTCs.
Check for DTCs.
DTC C1686 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the M116 parking assist ECU connector.
Disconnect the I7 outer rear view mirror assembly with cover RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M116-6 (RCB+) - I7-5 (RCB+) | Always | Below 1 Ω |
| M116-30 (RCV+) - I7-6 (RCV+) | Always | Below 1 Ω |
| M116-31 (RCV-) - I7-13 (RCV-) | Always | Below 1 Ω |
| M116-23 (RGND) - I7-12 (RGND) | Always | Below 1 Ω |
| M116-32 (SGND) - Body ground | Always | Below 1 Ω |
| M116-6 (RCB+) or I7-5 (RCB+) - Body ground | Always | 10 kΩ or higher |
| M116-30 (RCV+) or I7-6 (RCV+) - Body ground | Always | 10 kΩ or higher |
| M116-31 (RCV-) or I7-13 (RCV-) - Body ground | Always | 10 kΩ or higher |
| M116-23 (RGND) or I7-12 (RGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M116 parking assist ECU connector.
| *a | Component without harness connected
(Parking Assist ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M116-23 (RGND) - Body ground | Always | Below 1 Ω |
| M116-31 (RCV-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Remove the parking assist ECU with the connector still connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M116-23 (RGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M116-6 (RCB+) - M116-23 (RGND) | Engine switch on (IG) | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
| *a | Component with harness connected
(Parking Assist ECU) |
Using an oscilloscope, check the waveform of the side television camera assembly RH.
A waterproof connector is used for the side television camera assembly RH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
| *a | Waveform 1 (camera lens not covered, displaying an image) |
| *b | Waveform 2 (camera lens covered, blacking out the screen) |
| *c | Synchronization Signal |
| *d | Video Waveform |
The video waveform changes according to the image sent by the side television camera assembly RH.
The video waveform is constantly output when the engine switch is on (ACC).
| Item | Content |
|---|---|
| Tester Connection | M116-30 (RCV+) - M116-23 (RGND) |
| Tool Setting | 200 mV/DIV., 50 μs./DIV. |
| Condition | Engine switch on (IG), panoramic view monitor system operating |
Waveform is similar to that shown in illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the side television camera assembly RH with a new or known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Check for DTCs.
DTC C1683 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG