Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2019.09
RM32H0E _56 Audio / Visual / Telematics _060571 PARK ASSIST / MONITORING _0404351 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C168D  Vehicle Information Unmatched  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that the vehicle information received via CAN communication and the vehicle information stored in the parking assist ECU do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area
C168D Vehicle Information Unmatched Vehicle information unmatched
·

Camera view adjustment (calibration)

·

Steering angle setting

·

Parking assist ECU



CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.PERFORM SETTINGS (CAMERA VIEW ADJUSTMENT [CALIBRATION], STEERING ANGLE SETTING)
a.

Perform the following procedure depending on the memory conditions to register the vehicle information to the parking assist ECU.




Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C168D is not output.


HINT:
·

If DTC C168D is output, perform the procedure to allow the parking assist ECU to store the vehicle information again.

·

If DTC C168D is still output after performing the procedure to make the parking assist ECU store the vehicle information 3 times, replace the parking assist ECU.




Result:
Proceed to
OK
NG



OK

END (SETTINGS ARE DEFECTIVE)

NG

3.READ VALUE USING GTS
3.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Circumference Monitoring Camera Control Module / Data List.


e.

Read the Data List according to the display on the GTS.

Chassis > Panoramic View Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back Camera Availability Consistency Status of ECU stored in rear television camera assembly OK/NG OK: Normal
NG: Rear television camera assembly or parking assist ECU is abnormal
-
Side Camera LH Availability Consistency Status of ECU stored in side television camera assembly LH OK/NG OK: Normal
NG: Side television camera assembly LH or parking assist ECU is abnormal
-
Front Camera Availability Consistency Status of ECU stored in front television camera assembly OK/NG OK: Normal
NG: Front television camera assembly or parking assist ECU is abnormal
-
Side Camera RH Availability Consistency Status of ECU stored side television camera assembly RH OK/NG OK: Normal
NG: Side television camera assembly RH or parking assist ECU is abnormal
-
Chassis > Panoramic View Monitor > Data List
Tester Display
Back Camera Availability Consistency
Side Camera LH Availability Consistency
Front Camera Availability Consistency
Side Camera RH Availability Consistency
50003 353 53,54,55,56
Result:
Result Proceed to
"NG" is displayed for any of the following items:
·

Back Camera Availability Consistency

·

Side Camera LH Availability Consistency

·

Front Camera Availability Consistency

·

Side Camera RH Availability Consistency


A
"OK" is displayed for all items. B




A

ADJUST PANORAMIC VIEW MONITOR SYSTEM DISPLAY SETTING

B