This DTC is stored if the parking assist ECU judges as a result of its self check that a problem with the current supplied from the rear television camera assembly, front television camera assembly, side television camera assembly RH and side television camera assembly LH to the parking assist ECU.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1688 | Camera Supply Voltage Malfunction (Back or Front or RH Side or LH Side) | Camera current malfunction | ·
Harness or connector ·
Parking assist ECU ·
Rear television camera assembly ·
Front television camera assembly ·
Side television camera assembly RH ·
Outer rear view mirror assembly with cover RH ·
Side television camera assembly LH ·
Outer rear view mirror assembly with cover LH |
When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION
Clear the DTCs.
Check for DTCs.
DTC C1688 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the S11 rear television camera assembly connector.
Disconnect the M116 parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S11-6 (CB+) - M116-8 (CB+) | Always | Below 1 Ω |
| S11-5 (CGND) - M116-25 (CGND) | Always | Below 1 Ω |
| S11-6 (CB+) or M116-8 (CB+) - Body ground | Always | 10 kΩ or higher |
| S11-5 (CGND) or M116-25 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M116 parking assist ECU connector.
Disconnect the B17 front television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M116-7 (BCB+) - B17-6 (BCB+) | Always | Below 1 Ω |
| M116-24 (BGND) - B17-5 (BGND) | Always | Below 1 Ω |
| M116-7 (BCB+) or B17-6 (BCB+) - Body ground | Always | 10 kΩ or higher |
| M116-24 (BGND) or B17-5 (BGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M116 parking assist ECU connector.
Disconnect the I7 outer rear view mirror assembly with cover RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M116-6 (RCB+) - I7-5 (RCB+) | Always | Below 1 Ω |
| M116-23 (RGND) - I7-14 (RGND) | Always | Below 1 Ω |
| M116-6 (RCB+) or I7-5 (RCB+) - Body ground | Always | 10 kΩ or higher |
| M116-23 (RGND) or I7-14 (RGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M116 parking assist ECU connector.
Disconnect the J11 outer rear view mirror assembly with cover LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M116-9 (LCB+) - J11-5 (LCB+) | Always | Below 1 Ω |
| M116-26 (LGND) - J11-14 (LGND) | Always | Below 1 Ω |
| M116-9 (LCB+) or J11-5 (LCB+) - Body ground | Always | 10 kΩ or higher |
| M116-26 (LGND) or J11-14 (LGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Remove the parking assist ECU with the connector still connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M116-25 (CGND) - Body ground | Always | Below 1 Ω |
| M116-24 (BGND) - Body ground | Always | Below 1 Ω |
| M116-23 (RGND) - Body ground | Always | Below 1 Ω |
| M116-26 (LGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M116-8 (CB+) - M116-25 (CGND) | Engine switch on (IG) | 5.5 to 7.05 V |
| M116-7 (BCB+) - M116-24 (BGND) | Engine switch on (IG) | 5.5 to 7.05 V |
| M116-6 (RCB+) - M116-23 (RGND) | Engine switch on (IG) | 5.5 to 7.05 V |
| M116-12 (LCB+) - M116-26 (LGND) | Engine switch on (IG) | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B17 front television camera assembly connector.
Disconnect the I7 outer rear view mirror assembly with cover RH connector.
Disconnect the J11 outer rear view mirror assembly with cover LH connector.
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| The rear view screen is displayed and DTC C1688 is not output | A |
| The rear view screen is not displayed and DTC C1688 is output | B |
A
B
Disconnect the S11 rear television camera assembly connector.
Disconnect the I7 outer rear view mirror assembly with cover RH connector.
Disconnect the J11 outer rear view mirror assembly with cover LH connector.
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| The front view screen is displayed and DTC C1688 is not output | A |
| The front view screen is not displayed and DTC C1688 is output | B |
A
B
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Front)>REMOVAL
Disconnect the B7 front television camera assembly connector.
Disconnect the J13 outer rear view mirror assembly with cover RH connector.
Disconnect the R5 rear television camera assembly connector.
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| The side view screen is displayed and DTC C1688 is not output | A |
| The side view screen is not displayed and DTC C1688 is output | B |
A
B
Replace the side television camera assembly RH with a new or known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Check for DTCs.
DTC C1688 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the side television camera assembly LH with a new or known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Check for DTCs.
DTC C1688 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG