Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › from 2019.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P05042B  Brake Switch "A"/"B" Signal Cross Coupled  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores this DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).


On the GTS, Data List item Stop Light SW is ON when the brake pedal is depressed.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P05042B Brake Switch "A"/"B" Signal Cross Coupled Conditions (a) and (b) are met for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch ON
(b) STP signal OFF when ST1- signal OFF
·

Open or short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


Does not come on DTC stored SAE Code:
P0504

WIRING DIAGRAM

A384827E17
6.281,0.333 6.74,0.531 0.458,0.198 10 false STP 6.281,1.125 6.74,1.323 0.458,0.198 10 false ST1- 6.458,2.688 6.917,2.885 0.458,0.198 10 false ECM 4.667,2.604 5.823,3.135 1.156,0.531 10 false Stop Light Switch Assembly 0.604,3.844 1.729,4.104 1.125,0.26 10 false Battery 4.365,3.542 6.833,4.135 2.469,0.594 10 false from Smart Key ECU Assembly*1 or Ignition or Starter Switch Assembly*2 6.469,2.542 6.927,2.74 0.458,0.198 10 false A38 4.667,2.448 5.125,2.646 0.458,0.198 10 false A91 4.698,1.844 5.156,2.042 0.458,0.198 10 false GND 4.719,1.24 5.177,1.438 0.458,0.198 10 false B 4.719,0.427 5.177,0.625 0.458,0.198 10 false B 4.51,0.344 4.969,0.542 0.458,0.198 10 false 7 4.51,1.135 4.969,1.333 0.458,0.198 10 false 6 4.531,1.771 4.99,1.969 0.458,0.198 10 false 2 6.01,1.125 6.469,1.323 0.458,0.198 10 false 10 6.073,0.333 6.531,0.531 0.458,0.198 10 false 9 5.563,0.438 6.021,0.635 0.458,0.198 10 false L 5.563,1.24 6.021,1.438 0.458,0.198 10 false L 5.76,1.135 6.219,1.333 0.458,0.198 10 false 5 5.76,0.333 6.219,0.531 0.458,0.198 10 false 3 0.396,2.229 1.875,2.427 1.479,0.198 10 false BATT MAIN 0.594,0.604 1.104,0.802 0.51,0.198 10 false J/B-B 3.292,0.604 3.906,0.802 0.615,0.198 10 false STOP 2.99,1.385 4.042,1.594 1.052,0.208 10 false ECU-IG2 NO. 3 2.167,2.167 2.896,2.375 0.729,0.208 10 false IG2-NO. 2 1.521,2.438 3.583,3.042 2.063,0.604 10 false Instrument Panel Junction Block Assembly 1.781,3.948 3.833,4.313 2.052,0.365 10 false *1: w/ Entry and Start System 1.781,4.333 3.958,4.688 2.177,0.354 10 false *2: w/o Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch assembly conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine / Data List / All Data / Stop Light SW.

(e)

Check the Data List indication when the brake pedal is depressed and released.

Brake Pedal Operation Stop Light SW
Depressed ON
Released OFF




PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
A418954C44
1.5,0.25 1.917,0.5 0.417,0.25 2.25,1.208 2.667,0.458 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.583,0.292 2.042,0.49 0.458,0.198 10 false A91 2.708,0.375 3.167,0.573 0.458,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


a.

Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A91-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STOP LIGHT SWITCH ASSEMBLY)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
A418954C45
0.5,0.958 0.917,1.26 0.417,0.302 2.313,1.813 2.073,1.344 true 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a 0.583,1.031 1.042,1.229 0.458,0.198 10 false A91 2.344,1.844 2.5,2.042 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


a.

Disconnect the stop light switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A91-6 (B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 RELAY - STOP LIGHT SWITCH ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the A91 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A91-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

5.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)
a.

Disconnect the ECM connector.

A395444C01
4.083,0.75 4.583,1 0.5,0.25 5.219,1.563 5.875,0.865 true 6.083,1.573 5.948,0.865 true 1.073,1.406 1.385,1.563 0.313,0.156 10 false *a 2.792,1.406 3.104,1.563 0.313,0.156 10 false *b 4.438,0.208 4.75,0.365 0.313,0.156 10 false *c 4.198,0.771 4.656,0.969 0.458,0.198 10 false A38 5.052,1.573 5.51,1.771 0.458,0.198 10 false STP 5.979,1.583 6.438,1.781 0.458,0.198 10 false ST1-
*a Brake Pedal Depressed *b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)
- -



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-10 (ST1-) - Body ground Brake pedal released 7.5 to 14 V
Brake pedal depressed Below 1.5 V
A38-9 (STP) - Body ground Brake pedal released Below 1.5 V
Brake pedal depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)