Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › ECM › 2019.09–2020.08
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0295066 ECM A

8NR-FTS ENGINE CONTROL  ECM  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the ECM removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-collision syatem
Parking support brake system*1
Initialize back door lock Power door lock control system (Click here)
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration
·

MIL illuminates

·

DTC P0630 is stored


(Click here)
HEAVY KNOCK HISTORY
·

SAVE HISTORY

·

WRITE HISTORY


(Click here)
ECU Communication ID Registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Smart entry and start system

·

Engine start function

·

Steering lock system


See Service Bulletin for the registration method. (w/ Entry and Start System)
Engine starting See Service Bulletin for the registration method. (w/o Entry and Start System)
1.

Reset Memory

2.

Deceleration Sensor 0 Point Calibration

3.

CVT Oil Pressure Calibration


Deterioration of fuel efficiency for K313(Click here)
for K313F(Click here)

PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

If the ECM has been struck or dropped, replace it.

·

Perform the Vehicle Identification Number (VIN) registration when replacing the ECM.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION

·

When replacing the ECM, use the GTS to save "Heavy Knock History" and then upload it to the new ECM.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 53141F 3.REMOVE RADIATOR COVER

Hide 17751 4.REMOVE NO. 1 AIR CLEANER INLET

Hide 17705 5.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

a.
A395310

Disconnect the mass air flow meter connector.


b.

Disengage the clamp from the air cleaner cap sub-assembly.


c.
A395311

Disengage the 2 air cleaner cap sub-assembly clamps.


d.
A395312

Disengage the 2 guides to separate the air cleaner cap sub-assembly from the air cleaner case sub-assembly.


e.

Loosen the hose clamp and remove the air cleaner cap sub-assembly from the air cleaner hose.


Hide 17701 6.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 89661 7.REMOVE ECM

HINT:

When replacing the ECM, use the GTS to save "Heavy Knock History" and then upload it to the new ECM.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION


a.
A390459

Remove the No. 1 relay block cover from the No. 1 engine room relay block.


b.
A394708

Raise the 2 levers while pushing the locks on the levers, and disconnect the 2 ECM connectors.

NOTICE:

After disconnecting the ECM connectors, make sure that dirt, water or other foreign matter does not contact the connecting parts of the ECM connectors.



c.
A394709

Disconnect the 3 connectors from the No. 1 engine room relay block.


d.

Disengage the 2 claws to separate the engine wire from the No. 1 engine room relay block.


e.
A394707

Remove the bolt, nut and ECM.

NOTICE:

If the ECM has been struck or dropped, replace it.



Hide 89667E 8.REMOVE NO. 1 ECM BRACKET

a.
A394665

Remove the 2 screws and No. 1 ECM bracket from the ECM.


Hide 89668 9.REMOVE NO. 2 ECM BRACKET

a.
A394664

Remove the 2 screws and No. 2 ECM bracket from the ECM.