Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK › 2019.09–2020.08
RM32H0E _58 Vehicle Interior _059647 DOOR LOCK _0292600 REAR DOOR LOCK A

DOOR LOCK  REAR DOOR LOCK  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear door lock with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal (for Audio and Visual System).

·

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal (for Navigation System (for Radio and Display Type)).



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67498 3.REMOVE REAR DOOR REAR FRAME BRACKET

Hide 69284D 4.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

Hide 84810 5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL

Hide 67604 6.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 67628 7.REMOVE REAR DOOR TRIM BRACKET

Hide 67842E 8.REMOVE REAR DOOR SERVICE HOLE COVER

Hide 69240 9.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY

Hide 69227L 10.REMOVE REAR DOOR OUTSIDE HANDLE COVER

Hide 69060A 11.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY

a.
B450677

Disconnect the connector.


b.

Using a T30 "TORX" socket wrench, remove the 3 screws and rear door lock with motor assembly.


c.

When reusing the rear door lock with motor assembly:

i.
B450678

Remove the door lock wiring harness seal from the rear door lock with motor assembly.



Hide 69740D 12.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.

w/o Double Locking System:

i.
B450679C01
1.323,1.458 0.729,1.302 true 0.521,1.208 0.833,1.365 0.313,0.156 10 false *a
*a Protective Tape
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped in protective tape, disengage the claw as shown in the illustration.


ii.
B450680

Disengage the guide to remove the rear door lock remote control cable assembly from the rear door lock with motor assembly.



b.

w/ Double Locking System:

i.
B450685C01
1.208,1.26 0.542,0.938 true 0.354,0.823 0.625,1.021 0.271,0.198 10 false *a
*a Protective Tape
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped in protective tape, disengage the claw as shown in the illustration.


ii.
B450686

Disengage the guide to remove the rear door lock remote control cable assembly from the rear door lock with motor assembly.



Hide 69780B 13.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

a.

w/o Double Locking System:

i.
B450683C01
2.24,0.875 1.813,0.615 true 1.583,0.521 1.802,0.719 0.219,0.198 10 true *a
*a Protective Tape
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.


ii.
B450684

Disengage the guide to remove the rear door inside locking cable assembly from the rear door lock with motor assembly.



b.

w/ Double Locking System:

i.
B450687C01
2.104,1.021 1.615,0.802 true 1.385,0.698 1.615,0.896 0.229,0.198 10 true *a
*a Protective Tape
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.


ii.
B450688

Disengage the guide to remove the rear door inside locking cable assembly from the rear door lock with motor assembly.



Hide 69730E 14.REMOVE NO. 1 REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B450681C01
2.323,1.563 2.656,1.167 true 2.677,1.052 2.99,1.208 0.313,0.156 10 false *a
*a Protective Tape
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.


b.
B450682

Disengage the guide to remove the No. 1 rear door lock remote control cable assembly from the rear door lock with motor assembly.