Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2019.09–2020.08
RM32H0E _59 Vehicle Exterior _060017 DOOR / HATCH _0295667 REAR DOOR A

DOOR / HATCH  REAR DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the rear door disassembly/reassembly are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
·

Door window regulator assembly

·

Door glass

·

Door glass run


Initialize Power Window Control System
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal (for Audio and Visual System).

·

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal (for Navigation System (for Radio and Display Type)).



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67498 3.REMOVE REAR DOOR REAR FRAME BRACKET

a.
B458141C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws and clip to remove the rear door rear frame bracket as shown in the illustration.


Hide 69284D 4.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

a.
B458142C01
0,0 0,0 false
V113147

Remove in this Direction


Using a moulding remover A, disengage the claws to remove the rear door inside handle bezel plug as shown in the illustration.


Hide 84810D 5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL

a.
B458143C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws, clips and guides as shown in the illustration.


b.
B458144

Disconnect the connector to remove the rear power window regulator switch assembly with rear door armrest base upper panel.


Hide 67604 6.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B458145

Remove the 3 screws.


b.
B458146C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Remove the 2 screws.


c.

Disengage the clips and guide as shown in the illustration.


d.
B458220C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws as shown in the illustration.


e.
B539826C01
2.5,0.99 2.917,0.573 true 1.938,1.76 2.438,1.26 true 2.917,0.469 3.135,0.656 0.219,0.188 10 true *1 1.75,1.688 1.948,1.885 0.198,0.198 10 true *2
*1 Rear Door Inside Locking Cable Assembly
*2 Rear Door Lock Remote Control Cable Assembly
V113147

Remove in this Direction


Disengage the guides to disconnect the rear door inside locking cable assembly and rear door lock remote control cable assembly to remove the rear door trim board sub-assembly as shown in the illustration.


Hide 69206C 7.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B458148

Disengage the claw and guides to remove the front door inside handle sub-assembly.


Hide 68199 8.REMOVE REAR DOOR BELT REAR SEAL

a.
B458149

Remove the rear door belt rear seal.


Hide 68174A 9.REMOVE REAR DOOR GLASS INNER WEATHERSTRIP

a.
B458150C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door glass inner weatherstrip with the rear door belt seal as shown in the illustration.


Hide 68197 10.REMOVE REAR DOOR BELT SEAL

a.
B458151C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door belt seal from the rear door glass inner weatherstrip as shown in the illustration.


Hide 11.REMOVE HOLE PLUG

a.
B458154

Remove the 2 hole plugs.


Hide 67676C 12.REMOVE NO. 2 REAR DOOR FRAME GARNISH

a.
B465116

Remove the No. 2 rear door frame garnish.


Hide 67628 13.REMOVE REAR DOOR TRIM BRACKET

a.
B458153

Remove the 2 screws and rear door trim bracket.


Hide 67842E 14.REMOVE REAR DOOR SERVICE HOLE COVER

a.
B458152C02
0,0 0,0 false
V100143

Butyl Tape


Remove the rear door service hole cover.

HINT:

Remove any remaining butyl tape from the rear door panel.



Hide 68640A 15.REMOVE REAR DOOR CHECK ASSEMBLY

a.
B539827

Remove the 3 bolts and rear door check assembly.


Hide 67868D 16.REMOVE REAR DOOR WEATHERSTRIP

a.
B458157C03
2.958,0.583 3.104,0.333 false 3.167,0.156 3.354,0.354 0.188,0.198 10 false *a
*a Clip (A)
V100155

Double-sided Tape


Using a clip remover, disengage the clip (A) and other clips.


b.

Remove the double-sided tape and rear door weatherstrip.

NOTICE:

Remove any remaining double-sided tape from the rear door panel.



Hide 67408F 17.REMOVE REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY

a.
B458155

Remove the screw and 2 bolts.


b.

Remove the rear door window rear lower frame sub-assembly from the rear door glass run.


Hide 68104 18.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

a.
B458158

Disengage the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

NOTICE:

After separating the rear door glass sub-assembly, do not allow it to fall.



b.
B458159C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the rear door glass sub-assembly as shown in the illustration.

NOTICE:

Do not damage the rear door glass sub-assembly.



Hide 69906B 19.REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY (for LED Type Turn Signal Light)

a.
B458160C01
0.917,0.75 1.302,1.156 true 0.719,0.656 1.031,0.813 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, remove the rear door glass channel sub-assembly.


Hide 69975A 20.REMOVE REAR DOOR GLASS CHANNEL FILLER (for LED Type Turn Signal Light)

a.
B458161C01
1.26,1.177 0.99,0.833 true 0.813,0.729 1.125,0.885 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, remove the rear door glass channel filler from the rear door glass sub-assembly.


Hide 67674A 21.REMOVE REAR DOOR FRAME GARNISH

a.
B458163

Disengage the guides to remove the rear door frame garnish.


Hide 68152C 22.REMOVE REAR DOOR GLASS RUN

a.
B458162

Remove the rear door glass run.


Hide 23.REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY

a.
B458164C01
1.938,0.573 2.354,0.156 true 2.427,0.052 2.594,0.219 0.167,0.167 10 true *a
*a Temporary Bolt


Disconnect the connector.


b.

Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator sub-assembly may fall and cause damage.



c.

Remove the 3 bolts and rear door window regulator sub-assembly.


d.

Remove the temporary bolt from the rear door window regulator sub-assembly.


Hide 68124B 24.REMOVE REAR DOOR QUARTER WINDOW GLASS

a.
B458165C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door quarter window glass with rear door quarter window weatherstrip as shown in the illustration.


Hide 68189 25.REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP

a.
B458166

Remove the rear door quarter window weatherstrip from the rear door quarter window glass.


Hide 75740 26.REMOVE REAR DOOR BELT MOULDING ASSEMBLY

Hide 69240 27.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B458168

Disconnect the No. 1 rear door lock remote control cable assembly from the clamps.


b.
B458169

Remove the 3 bolts.


c.
B506810C01
0,0 0,0 false
V100155

Double-sided Tape


Peel back the double-sided tape.


d.
B505866C01
0,0 0,0 false
V100135

Push


Disengage the claws from the rear door service hole as shown in the illustration to separate the rear door outside handle assembly together with the rear door outside handle cover as a single unit.

CAUTION:

Be careful not to cut your hands or fingers on the edge of the rear door panel.


HINT:

If your hands cannot fit, use a tool such as a screwdriver with its tip wrapped in protective tape to disengage the claws.



e.
B458170

Disengage the guide to disconnect the No. 1 rear door lock remote control cable assembly to remove the rear door outside handle assembly with the rear door outside handle cover.

NOTICE:

Remove any remaining double-sided tape from the rear door panel.



Hide 69227L 28.REMOVE REAR DOOR OUTSIDE HANDLE COVER

a.
B465117

Disengage the clips and guide to remove the rear door outside handle cover.


Hide 69229A 29.REMOVE NO. 3 DOOR OUTSIDE HANDLE CAP

a.
B539828C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the 2 No. 3 door outside handle caps.


Hide 69060A 30.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY

Hide 67837C 31.REMOVE REAR DOOR DUST PROOF SEAL (for TMMT Made)

a.
B458172

Remove the 3 rear door dust proof seals.


Hide 67837C 32.REMOVE REAR DOOR DUST PROOF SEAL (for TMC Made)

a.

for Type A:

i.
B458172

Remove the 3 rear door dust proof seals.

NOTICE:

When installing, install 2 dust proof seals in the same way as for type B.




b.

for Type B:

i.
B621534

Remove the 2 rear door dust proof seals.



Hide 86160B 33.REMOVE REAR SPEAKER ASSEMBLY

Hide 67003C 34.REMOVE REAR DOOR PANEL CUSHION

a.
B458171

Disengage the claws to remove the 2 rear door panel cushions.


Hide 75076 35.REMOVE REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY

Hide 75742 36.REMOVE REAR DOOR OUTSIDE MOULDING

Hide 75764A 37.REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING

Hide 75766A 38.REMOVE REAR DOOR REAR WINDOW FRAME MOULDING

Hide 75978H 39.REMOVE REAR DOOR LOWER OUTSIDE STRIPE (w/ Stripe Tape)

Hide 75988E 40.REMOVE REAR DOOR OUTSIDE STRIPE (w/ Stripe Tape)