Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1.REMOVE REAR SPOILER
85110R
2.REMOVE REAR WIPER MOTOR ASSEMBLY
85110R
3.REMOVE REAR LIGHT ASSEMBLY (for Bulb Type)
85110R
4.REMOVE REAR LIGHT ASSEMBLY (for LED Type)
86300C
5.DISCONNECT NO. 2 AMPLIFIER ANTENNA ASSEMBLY (w/ Woofer)
Disconnect the connector.
82184
6.DISCONNECT NO. 1 BACK DOOR WIRE
Disconnect the 2 connectors from the back door glass.
w/ Glass Breakage Sensor:
Disconnect the connector from the glass breakage sensor.
68131
7.REMOVE BACK DOOR GLASS
Disconnect each connector and disengage each clamp.
|
Protective Tape |
Apply protective tape to the area around the installation position of the back door glass on the back door panel to prevent it from being scratched.
| *a | Matchmark |
Place matchmarks on the back door glass and back door panel at the locations indicated in the illustration.
Matchmarks are not necessary if the back door glass is not going to be reused.
| *1 | No. 1 Back Window Glass Spacer |
| *2 | No. 2 Back Window Glass Spacer |
| *a | Piano Wire |
Pass a piano wire between the back door panel and back door glass from the interior.
Tie both wire ends to wooden blocks or similar objects that can serve as handles.
Cut the adhesive by pulling the piano wire around the back door glass.
When separating the back door glass, take care not to damage the paint or interior and exterior ornaments.
When cutting the adhesive, take care not to damage the connectors on the back door glass.
Do not pull the piano wire in a vertical direction, but pull it in a horizontal direction.
Using suction cups, disengage the No. 1 back window glass spacer and No. 2 back window glass spacer and remove the back door glass.
To prevent the back door glass from falling when performing this operation, be sure to hold the back door glass using suction cups.
Be careful not to drop the back door glass.
Leave as much adhesive on the back door panel as possible when removing the back door glass.
75574B
8.REMOVE BACK WINDOW OUTSIDE MOULDING LH
When reusing the back door glass:
| *a | Back Side of Back Door Glass |
Using a scraper, remove the back window outside moulding LH.
Be careful not to damage the back door glass.
Be sure to replace the back window outside moulding LH with a new one.
75574B
9.REMOVE BACK WINDOW OUTSIDE MOULDING RH
Use the same procedure as for the LH side.
64819B
10.REMOVE NO. 2 BACK WINDOW GLASS SPACER
When reusing the back door glass:
| *a | Back Side of Back Door Glass |
Using a scraper, remove the No. 2 back window glass spacer.
Be careful not to damage the back door glass.
Be sure to replace the No. 2 back window glass spacer with a new one.
64818C
11.REMOVE NO. 1 BACK WINDOW GLASS SPACER
Use the same procedure as for the No. 2 back window glass spacer.
75575D
12.REMOVE BACK WINDOW LOWER MOULDING (for Type A)
When reusing the back door glass:
| *a | Back Side of Back Door Glass |
Using a scraper, remove the back window lower moulding.
Be careful not to damage the back door glass.
Be sure to replace the back window lower moulding with a new one.
75575D
13.REMOVE BACK WINDOW LOWER MOULDING (for Type B)
When reusing the back door glass:
| *a | Back Side of Back Door Glass |
Using a scraper, remove the back window lower moulding.
Be careful not to damage the back door glass.
Be sure to replace the back window lower moulding with a new one.
14.REMOVE BACK DOOR GLASS SPACER (for Upper Side)
When reusing the back door glass:
| *a | Back Side of Back Door Glass |
Using a scraper, remove the 2 back door glass spacers.
Be careful not to damage the back door glass.
Be sure to replace the back door glass spacer with a new one.
15.REMOVE BACK DOOR GLASS SPACER (for Lower Side)
When reusing the back door glass (for Type B):
| *a | Back Side of Back Door Glass |
Using a scraper, remove the 2 back door glass spacers.
Be careful not to damage the back door glass.
Be sure to replace the back door glass spacer with a new one.
16.REMOVE BACK DOOR GLASS SPACER (for Side)
| *a | Back Side of Back Door Glass |
When reusing the back door glass (for Type A):
Using a scraper, remove the 4 back door glass spacers.
Be careful not to damage the back door glass.
Be sure to replace the back door glass spacer with a new one.
| *a | Back Side of Back Door Glass |
When reusing the back door glass (for Type B):
Using a scraper, remove the 2 back door glass spacers.
Be careful not to damage the back door glass.
Be sure to replace the back door glass spacer with a new one.