75431A
1.INSTALL NO. 1 BACK DOOR EMBLEM
75444A
2.INSTALL NO. 4 BACK DOOR NAME PLATE (for AWD)
75442A
3.INSTALL NO. 2 BACK DOOR NAME PLATE
75441E
4.INSTALL NO. 1 BACK DOOR NAME PLATE (w/ Brand Mark)
5.INSTALL HOLE PLUG
Install the hole plug.
81584
6.INSTALL REAR LIGHT PACKING
81590A
7.INSTALL REAR LIGHT ASSEMBLY LH
81580D
8.INSTALL REAR LIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
67894B
9.INSTALL NO. 2 BACK DOOR PANEL PROTECTOR
Clean vehicle installation surface.
Remove the release paper from a new No. 2 back door panel protector.
|
Double-sided Tape |
Engage the clips to install the No. 2 back door panel protector.
Press the double-sided tape area of the No. 2 back door panel protector.
67893A
10.INSTALL NO. 1 BACK DOOR PANEL PROTECTOR
Use the same procedure for the No. 2 back door panel protector.
67005B
11.INSTALL BACK DOOR PANEL CUSHION
Engage the claws to install the 2 back door panel cushions.
86790D
12.INSTALL REAR TELEVISION CAMERA ASSEMBLY (w/ Rear View Monitor System)
76827A
13.INSTALL NO. 2 BACK DOOR GARNISH RETAINER (w/o Rear View Monitor System)
Engage the claws to install the No. 2 back door garnish retainer.
81270B
14.INSTALL LICENSE PLATE LIGHT ASSEMBLY
84840G
15.INSTALL BACK DOOR OPENER SWITCH ASSEMBLY
16.INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY
w/o Cover:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BACK DOOR OUTSIDE GARNISH>INSTALLATION
w/ Cover:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BACK DOOR OUTSIDE GARNISH>INSTALLATION
81962
17.INSTALL REAR LIGHT COVER LH (w/ Cover)
81952A
18.INSTALL REAR LIGHT COVER RH (w/ Cover)
Use the same procedure as for the LH side.
85345R
19.INSTALL REAR WASHER NOZZLE
20.INSTALL REAR SPOILER ASSEMBLY
67282F
21.INSTALL BACK DOOR LOWER STOPPER
Engage the guide and install the back door lower stopper.
Install a new bolt.
Use the same procedure for the RH side and LH side.
85110R
22.INSTALL REAR WIPER MOTOR ASSEMBLY
85143R
23.INSTALL REAR WIPER MOTOR GROMMET
24.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY
69350P
25.INSTALL BACK DOOR LOCK ASSEMBLY
69321
26.INSTALL BACK DOOR LOCK COVER
Clean vehicle installation surface.
Remove the release paper from a new back door lock cover.
|
Double-sided Tape |
Engage the claws to install the back door lock cover.
Press the double-sided tape area of the back door lock cover.
67765A
27.INSTALL BACK DOOR SERVICE HOLE COVER LH
Engage the claws to install the back door service hole cover LH.
67765A
28.INSTALL BACK DOOR SERVICE HOLE COVER RH
Use the same procedure as for the LH side.
67765A
29.INSTALL NO. 3 BACK DOOR SERVICE HOLE COVER
Engage the claws to install the No. 3 back door service hole cover.
67765A
30.INSTALL NO. 2 BACK DOOR SERVICE HOLE COVER
Use the same procedure as for the No. 1 back door service hole cover.
67765A
31.INSTALL NO. 1 BACK DOOR SERVICE HOLE COVER
Engage the claws to install the No. 1 back door service hole cover.
74811B
32.INSTALL DOOR PULL HANDLE
Engage the claws to install the door pull handle.
64780A
33.INSTALL BACK DOOR TRIM PANEL ASSEMBLY
Engage the clips to install the back door trim panel assembly.
64338D
34.INSTALL PACKAGE TRAY TRIM GARNISH HOOK
Use the same procedure for the RH side and LH side.
Install the package tray trim garnish hook.
Install the screw.
67938A
35.INSTALL BACK DOOR SIDE GARNISH LH
Engage the claws and clips to install the back door side garnish LH.
67937B
36.INSTALL BACK DOOR SIDE GARNISH RH
Use the same procedure as for the LH side.
64790B
37.INSTALL BACK DOOR TRIM UPPER PANEL ASSEMBLY
Engage the claws and clips to install the back door trim upper panel assembly.
64910J
38.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
64330D
39.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)
40.PERFORM CALIBRATION (w/ Panoramic View Monitor System)