Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › from 2019.09
RM32H0E _58 Vehicle Interior _059856 INTERIOR PANELS / TRIM _0293792 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 63311C 1.INSTALL ROOF HEADLINING

a.
B461368C01
0,0 0,0 false
V113147

Install in this Direction


Insert the roof headlining assembly into the cabin from the back door.

NOTICE:
·

Check that the corners of the roof headlining are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.

·

Make sure that the roof headlining does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining or vehicle interior.




b.
B461366

Engage the guides and set the roof headlining assembly.


c.

Install the 3 clips.


d.
B461388

w/ Lane Departure Alert System:

i.

Connect the ground wire with the nut.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)



e.
B461365C01
0.625,1.083 0.958,1.083 true 1.229,1.906 1.229,1.573 true 1.958,1.469 1.958,1.135 true 2.573,0.865 2.906,0.865 true 0.385,0.969 0.625,1.208 0.24,0.24 12 true *A 1.865,1.5 2.104,1.76 0.24,0.26 12 true *B 2.927,0.76 3.188,1.01 0.26,0.25 12 true *C 1.146,1.906 1.417,2.146 0.271,0.24 12 true *A
*A w/ Lane Departure Alert System
*B w/ EC Mirror
*C w/ Rain Sensor


for Windshield Glass Side:

i.

Connect each connector.



f.
B461364

for Rear Pillar RH Side:

i.

Connect the connector.



g.
B461362

for Front Pillar RH Side:

i.

Engage the wire harness clamps.


ii.

Connect the connector.



h.
B461363

for Front Pillar LH Side:

i.

Engage the wire harness clamps.


ii.

Connect each connector.



Hide 74612 2.INSTALL ASSIST GRIP COVER

HINT:

Use the same procedures for the opposite side.


a.
B445167

Install the 2 assist grip covers and 2 clips to the assist grip sub-assembly.


Hide 74610A 3.INSTALL ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedures for the opposite side.


a.
B461360C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clips to install the assist grip sub-assembly as shown in the illustration.


Hide 74348 4.INSTALL VISOR HOLDER

HINT:

Use the same procedures for the opposite side.


a.
B461355C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the base as shown in the illustration.


b.
B461356C01
0,0 0,0 false
V113147

Install in this Direction


Install the visor holder as shown in the illustration.


Hide 74320 5.INSTALL VISOR ASSEMBLY LH (w/o Vanity Light)

a.
B461352

Engage the guide to install the visor assembly LH.


b.

Using a T10H "TORX" driver, install the 2 screws.


Hide 74310 6.INSTALL VISOR ASSEMBLY RH (w/o Vanity Light)

HINT:

Use the same procedure as for the LH side.


Hide 74320 7.INSTALL VISOR ASSEMBLY LH (w/ Vanity Light)

Hide 74310 8.INSTALL VISOR ASSEMBLY RH (w/ Vanity Light)

HINT:

Use the same procedure as for the LH side.


Hide 74325 9.INSTALL VISOR BRACKET COVER

HINT:

Use the same procedures for the opposite side.


a.
B461351C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the visor bracket cover as shown in the illustration.


Hide 10.INSTALL COMMUNICATION TELEMATICS BOX ASSEMBLY (w/ Telematics Transceiver)

Hide 89732A 11.INSTALL THEFT WARNING ULTRASONIC SENSOR (w/ Intrusion Sensor)

Hide 81240 12.INSTALL NO. 1 ROOM LIGHT ASSEMBLY

Hide 81260A 13.INSTALL MAP LIGHT ASSEMBLY (for TMMT Made)

Hide 81260A 14.INSTALL MAP LIGHT ASSEMBLY (for TMC Made)

Hide 81340 15.INSTALL VANITY LIGHT ASSEMBLY (w/ Vanity Light)

Hide 87834 16.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ Cover)

Hide 86466D 17.INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Lane Departure Alert System)

Hide 86466E 18.INSTALL NO. 2 FORWARD RECOGNITION COVER (w/ Lane Departure Alert System)

Hide 89943 19.INSTALL RAIN SENSOR COVER (w/ Rain Sensor)

Hide 62480A 20.INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH

a.

When reusing the roof side inner garnish assembly LH (w/ Curtain Shield Airbag):

i.

Install 5 new clips to the roof side inner garnish assembly LH.



b.
B461349C02
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guide and clips to install the roof side inner garnish assembly LH as shown in the illustration.


Hide 62470A 21.INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 64740C 22.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

a.

Connect the rear seat 3 point type outer belt assembly LH.


b.
B461347C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clips and claws to install the deck trim side panel assembly LH as shown in the illustration.


c.

w/ Hook:

i.

Install the luggage hold belt striker with the bolt.



d.

w/o Hook:

i.

Install the clip.



Hide 64730B 23.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 64715C 24.INSTALL DECK TRIM SIDE COVER LH (w/ Cover)

a.
B461343C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guides to install the deck trim side cover LH as shown in the illustration.


b.
B459353

Turn the cover knob as shown in the illustration and lock it.


Hide 64714C 25.INSTALL DECK TRIM SIDE COVER RH (w/ Cover)

HINT:

Use the same procedure as for the LH side.


Hide 81330 26.INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

Hide 64716D 27.INSTALL DECK TRIM REAR COVER

a.
B459351C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides, claws and clips to install the deck trim rear cover as shown in the illustration.


b.

w/ Hook:

i.

Install the 2 luggage hold belt strikers with 2 bolts.



c.

w/o Hook:

i.

Install the 2 clips.



Hide 62420A 28.INSTALL CENTER PILLAR GARNISH ASSEMBLY LH

a.

When reusing the center pillar garnish assembly LH (w/ Curtain Shield Airbag):

i.

Install a new clip to the center pillar garnish assembly LH.



b.
B459347C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guides and clip to install the center pillar garnish assembly LH as shown in the illustration.


c.

Install the 2 clips.


Hide 62410A 29.INSTALL CENTER PILLAR GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62414A 30.INSTALL CENTER PILLAR LOWER GARNISH LH

a.
B459345C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clips and claws to install the center pillar lower garnish LH as shown in the illustration.


Hide 62413A 31.INSTALL CENTER PILLAR LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 73220 32.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 73210 33.CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 73233 34.INSTALL LAP BELT OUTER ANCHOR COVER

Hide 62552F 35.INSTALL REAR SEAT SIDE GARNISH LH

a.
B459343C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide, claws and clip to install the rear seat side garnish LH as shown in the illustration.


Hide 62551F 36.INSTALL REAR SEAT SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 71304C 37.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY LH

a.

Install the rear seatback hinge sub-assembly LH with the bolt.

Torque:
18.1 N*m (185 kgf*cm, 13 ft.*lbf)


Hide 71303C 38.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62332A 39.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62331A 40.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 67918A 41.INSTALL REAR DOOR SCUFF PLATE LH

a.
B459340C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the rear door scuff plate LH as shown in the illustration.


Hide 67917A 42.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62211 44.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62312B 45.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 46.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 62112 47.INSTALL COWL SIDE TRIM BOARD LH

Hide 62111C 48.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.


Hide 67914 49.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 67913 50.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 64997 51.INSTALL DECK FLOOR BOX LH (w/ Deck Floor Box)

a.
B459334C01
0,0 0,0 false
V113147

Install in this Direction


for Type A:

i.

Engage the guide to install the deck floor box LH as shown in the illustration.



b.
B459336C01
0,0 0,0 false
V113147

Install in this Direction


for Type B:

i.

Engage the guide to install the deck floor box LH as shown in the illustration.



c.
B459338C01
0,0 0,0 false
V113147

Install in this Direction


for Type C:

i.

Engage the guide to install the deck floor box LH as shown in the illustration.



Hide 64995 52.INSTALL DECK FLOOR BOX RH (w/ Deck Floor Box)

a.
B459328C01
0,0 0,0 false
V113147

Install in this Direction


for Type A:

i.

Engage the guide to install the deck floor box RH as shown in the illustration.



b.
B459330C01
0,0 0,0 false
V113147

Install in this Direction


for Type B:

i.

Engage the guide to install the deck floor box RH as shown in the illustration.



c.
B459332C01
0,0 0,0 false
V113147

Install in this Direction


for Type C:

i.

Engage the guide to install the deck floor box RH as shown in the illustration.



Hide 64777J 53.INSTALL SPARE WHEEL CUSHION

a.
B459320C01
0,0 0,0 false
V113147

Install in this Direction


for Type A:

i.

Install the spare wheel cushion as shown in the illustration.



b.
B459322C01
0,0 0,0 false
V113147

Install in this Direction


for Type B:

i.

Install the spare wheel cushion as shown in the illustration.



c.
B459324C01
0,0 0,0 false
V113147

Install in this Direction


for Type C:

i.

Install the spare wheel cushion as shown in the illustration.



d.
B459326C01
0,0 0,0 false
V113147

Install in this Direction


for Type D:

i.

Install the spare wheel cushion as shown in the illustration.


ii.

Install the clip.



Hide 58410B 54.INSTALL DECK BOARD ASSEMBLY

a.
B459312C01
0,0 0,0 false
V100155

Hook and Loop Fastener
V113147

Install in this Direction


for Type A:

i.

Install the deck board assembly as shown in the illustration.


ii.

Engage the hook and loop fastener.



b.
B459314C01
0,0 0,0 false
V113147

Install in this Direction


for Type B:

i.

Install the deck board assembly as shown in the illustration.



c.
B459316C01
0,0 0,0 false
V113147

Install in this Direction


for Type C:

i.

Install the deck board assembly as shown in the illustration.



d.
B459318C01
0,0 0,0 false
V113147

Install in this Direction


for Type D:

i.

Install the deck board assembly as shown in the illustration.



Hide 64910J 55.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

a.
B461528C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides to install the tonneau cover assembly as shown in the illustration.


b.
B461529

Engage the hooks.


Hide 64330D 56.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

a.
B557959C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides to install the package tray trim panel assembly as shown in the illustration.


b.
B461491

Engage the hooks.


Hide 57.INSTALL REAR SEAT ASSEMBLY

Hide 58.INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)

Hide 59.INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)

Hide 60.INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.