Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2019.09
RM32H0E _56 Audio / Visual / Telematics _060571 PARK ASSIST / MONITORING _0297206 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the blind spot monitor sensor.

WIRING DIAGRAM

E428351E01
0.167,0.688 1.115,1.115 0.948,0.427 10 false from IG1 NO. 1 Relay 1.552,0.885 2.563,1.125 1.01,0.24 10 false ECU-IG1 NO. 4 3.427,0.594 3.635,0.802 0.208,0.208 10 false 5 3.354,1.375 3.594,1.583 0.24,0.208 10 false 10 3.594,0.698 3.99,0.917 0.396,0.219 10 false BLB 3.594,1.479 4.083,1.698 0.49,0.219 10 false BLGD 3.219,4.604 3.708,4.823 0.49,0.219 10 false M63 3.208,4.771 4.844,5.156 1.635,0.385 10 false Blind Spot Monitor Sensor RH (Slave) 3.198,2.031 3.688,2.25 0.49,0.219 10 false M62 3.198,2.198 4.833,2.583 1.635,0.385 10 false Blind Spot Monitor Sensor LH (Master) 0.875,5.292 2.656,5.51 1.781,0.219 10 false : CAN Communication Line 3.594,4.063 4.083,4.281 0.49,0.219 10 false BRGD 3.354,3.969 3.594,4.177 0.24,0.208 10 false 10 3.583,3.271 3.979,3.49 0.396,0.219 10 false BRB 3.438,3.156 3.646,3.365 0.208,0.208 10 false 5 5.625,1.115 7.083,1.51 1.458,0.396 10 false to CAN Communication System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (MASTER) POWER SOURCE)
E360283C07
1.49,0.167 1.885,0.469 0.396,0.302 1.969,1.01 2.583,0.865 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 1.563,0.24 2.021,0.438 0.458,0.198 10 false M62 2.646,0.792 3.104,0.99 0.458,0.198 10 false BLB
*a Front view of wire harness connector
(to blind spot monitor sensor LH (Master))


a.

Disconnect the blind spot monitor sensor LH (Master) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M62-5 (BLB) - Body ground Ignition switch to ON 11 to 14 V
M62-5 (BLB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (MASTER) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (MASTER) - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M62-10 (BLGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (SLAVE) POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (SLAVE) POWER SOURCE)
E360283C08
1.49,0.167 1.885,0.469 0.396,0.302 1.969,1.031 2.521,0.99 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 1.563,0.24 2.021,0.438 0.458,0.198 10 false M63 2.573,0.906 3.031,1.104 0.458,0.198 10 false BRB
*a Front view of wire harness connector
(to blind spot monitor sensor RH(Slave))


a.

Disconnect the blind spot monitor sensor RH (Slave) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M63-5 (BRB) - Body ground Ignition switch to ON 11 to 14 V
M63-5 (BRB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (SLAVE) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (SLAVE) - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M63-10 (BRGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR