Home › Vehicle Interior › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY › 2019.09–2020.08
RM32H0E _58 Vehicle Interior _060065 SEAT BELT _0294238 REAR SEAT OUTER BELT ASSEMBLY A

SEAT BELT  REAR SEAT OUTER BELT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear seat outer belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

CAUTION:
·
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Wear protective gloves. Sharp areas on the parts may injure your hands.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
·
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If an SRS part is accidentally deployed, it may cause a serious injury.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE REAR SEAT ASSEMBLY

Hide 64330D 4.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

Hide 64910J 5.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

Hide 58410B 6.REMOVE DECK BOARD ASSEMBLY

Hide 64777J 7.REMOVE SPARE WHEEL CUSHION

Hide 64997 8.REMOVE DECK FLOOR BOX LH (w/ Deck Floor Box)

Hide 64995 9.REMOVE DECK FLOOR BOX RH (w/ Deck Floor Box)

Hide 67918A 10.REMOVE REAR DOOR SCUFF PLATE

Hide 62332A 11.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 71304C 12.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY

Hide 62552F 13.REMOVE REAR SEAT SIDE GARNISH

Hide 64716D 14.REMOVE DECK TRIM REAR COVER

Hide 81330 15.REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)

Hide 64715C 16.REMOVE DECK TRIM SIDE COVER (w/ Cover)

Hide 64740C 17.REMOVE DECK TRIM SIDE PANEL ASSEMBLY

Hide 62480A 18.REMOVE ROOF SIDE INNER GARNISH ASSEMBLY

Hide 73370 19.REMOVE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH (for LH Side)

a.
B458434

Remove the bolt to disconnect the floor anchor of the rear seat 3 point type outer belt assembly LH.


b.

w/o Pretensioner:

i.
B458439

Loosen the nut.


ii.
B458441

Remove the 3 bolts.


iii.

Disengage the guides to remove the rear seat 3 point type outer belt assembly LH with bracket.


iv.
B458445

Remove the nut.


v.

Disengage the guides to remove the rear seat 3 point type outer belt assembly LH from the outer belt anchor bracket sub-assembly LH.



c.

w/ Pretensioner:

i.
B458438

Loosen the nut.


ii.
B458440

Remove the 3 bolts.


iii.

Disengage the guides to separate the rear seat 3 point type outer belt assembly LH with bracket.


iv.
B458442C01
0.865,0.698 1.083,0.51 true 1.125,0.885 1.344,0.698 true 1.104,0.354 1.417,0.552 0.313,0.198 10 false *a 1.354,0.563 1.667,0.76 0.313,0.198 10 false *b
*a Locking Button
*b Protective Tape


Disengage the clamp.


v.

Using a screwdriver with its tip wrapped in protective tape, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.


vi.
B458444

Remove the nut.


vii.

Disengage the guides to remove the rear seat 3 point type outer belt assembly LH from the outer belt anchor bracket sub-assembly LH.



Hide 73360 20.REMOVE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH (for RH Side)

a.
B458435

Remove the bolt to disconnect the floor anchor of the rear seat 3 point type outer belt assembly RH.


b.

w/o Pretensioner:

i.
B458449

Loosen the nut.


ii.
B458451

Remove the 3 bolts.


iii.

Disengage the guides to remove the rear seat 3 point type outer belt assembly RH with bracket.


iv.
B460279

Remove the nut.


v.

Disengage the guides to remove the rear seat 3 point type outer belt assembly RH from the outer belt anchor bracket sub-assembly RH.



c.

w/ Pretensioner:

i.
B458446C01
0.875,0.708 1.115,0.521 true 1.146,0.917 1.385,0.729 true 1.146,0.396 1.458,0.594 0.313,0.198 10 false *a 1.385,0.615 1.698,0.813 0.313,0.198 10 false *b
*a Locking Button
*b Protective Tape


Disengage the clamp.


ii.

Using a screwdriver with its tip wrapped in protective tape, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.


iii.
B458449

Loosen the nut.


iv.
B458450

Remove the 3 bolts.


v.

Disengage the guides to remove the rear seat 3 point type outer belt assembly RH with bracket.


vi.
B460280

Remove the nut.


vii.

Disengage the guides to remove the rear seat 3 point type outer belt assembly RH from the outer belt anchor bracket sub-assembly RH.