This DTC is stored when the combination meter assembly detects a fuel sender gauge assembly malfunction via a direct line.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1501 | Sub Fuel Sender Open Detected | When IG voltage is 9.5 V or more and the following condition is detected:
·
Voltage signal from fuel sender gauge assembly is 0.2 V or less 3 times consecutively ·
Voltage signal from fuel sender gauge assembly is 4.7 V or more 3 times consecutively |
·
Harness or connector ·
Fuel tank vent tube assembly ·
No. 2 fuel sender gauge assembly ·
Combination meter assembly |
- |
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Fuel Input | Fuel input | Min.: 0 L, Max.: 127.5 L | ·
Fuel receiver gauge indicates F: 45.0 L ·
Fuel receiver gauge indicates 3/4: 36.0 L ·
Fuel receiver gauge indicates 1/2: 26.1 L ·
Fuel receiver gauge indicates 1/4: 14.1 L ·
Fuel receiver gauge indicates E: 5.0 L |
- |
| Tester Display |
|---|
| Fuel Input |
| Result | Proceed to |
|---|---|
| Fuel level data can be displayed on the GTS | A |
| Fuel level data cannot be displayed on the GTS | B |
A
B
| *a | Component with harness connected
(Combination Meter Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F4-16 (FV) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Combination Meter Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F4-22 (FR2) - F4-15 (EE&B) | Ignition switch ON | 0.2 to 4.7 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M76 fuel tank vent tube assembly connector.
Disconnect the F4 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M76-3 (FR) - F4-22 (FR2) | Always | Below 1 Ω |
| M76-2 (FE) - F4-15 (EE&B) | Always | Below 1 Ω |
| M76-1 (FV) - F4-16 (FV) | Always | Below 1 Ω |
| F4-22 (FR2) - Body ground | Always | 10 kΩ or higher |
| F4-15 (EE&B) - Body ground | Always | 10 kΩ or higher |
| F4-16 (FV) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 2 fuel sender gauge assembly.
Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (for AWD)>REMOVAL
Inspect the No. 2 fuel sender gauge assembly.
Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (for AWD)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Fuel Tank Vent Tube Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M76-1 (FV) - A-3 | Always | Below 1 Ω |
| M76-2 (FE) - A-2 | Always | Below 1 Ω |
| M76-3 (FR) - A-1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG