Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR (for Center Pillar) › 2019.09–2020.08
RM32H0E _58 Vehicle Interior _060061 SUPPLEMENTAL RESTRAINT SYSTEMS _0294201 SIDE AIRBAG SENSOR(for Center Pillar) A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR(for Center Pillar)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the floor side airbag sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.

·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
·
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If an SRS part is accidentally deployed, it may cause a serious injury.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 73233 3.REMOVE LAP BELT OUTER ANCHOR COVER

Hide 73220 4.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

Hide 67914 5.REMOVE FRONT DOOR SCUFF PLATE

Hide 62312B 6.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the front door opening trim weatherstrip to the extent that allows the removal of the center pillar lower garnish.


Hide 67918A 7.REMOVE REAR DOOR SCUFF PLATE

Hide 62332A 8.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the center pillar lower garnish.


Hide 62414A 9.REMOVE CENTER PILLAR LOWER GARNISH

Hide 89831E 10.REMOVE FLOOR SIDE AIRBAG SENSOR

a.

Check that the ignition switch off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B458401

Remove the bolt and disengage the claw to separate the floor side airbag sensor.


d.

Disconnect the connector to remove the floor side airbag sensor.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

B312073C30
4.354,1 4.896,0.979 true 3.813,1.75 3.813,1.365 false 0.74,2.448 0.271,1.875 true 4.156,0.708 4.531,0.646 true 4.938,0.875 5.25,1.031 0.313,0.156 10 false *a 3.74,1.792 4.052,1.948 0.313,0.156 10 false *b 0.125,1.719 0.438,1.875 0.313,0.156 10 false *c 4.583,0.531 4.896,0.76 0.313,0.229 10 false (A)
*a White Housing Lock *b Yellow CPA
*c Connector lock is released - -



ii.

Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.




e.

Check that the position of the white housing lock is as shown in the illustration.

B296255C05
4.76,1.833 5.031,2.104 0.271,0.271 10 false *b 1.396,1.833 1.677,2.115 0.281,0.281 10 false *b 4.76,0.573 5.031,0.875 0.271,0.302 10 false *a 1.396,0.573 1.677,0.865 0.281,0.292 10 false *a
*a Incorrect *b Correct