Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Rear) › from 2019.09
RM32H0E _56 Audio / Visual / Telematics _060571 PARK ASSIST / MONITORING _0298105 ULTRASONIC SENSOR(for Rear) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Rear)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during ultrasonic sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
·

Removal/installation of the rear center ultrasonic sensor

·

Removal/installation of the rear corner ultrasonic sensor

·

Replacement of the rear center ultrasonic sensor

·

Replacement of the rear corner ultrasonic sensor


·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Simple intelligent parking assist system

·

Toyota parking assist-sensor system

·

Parking support brake system


(Click here)

PROCEDURE

Hide 1.REMOVE REAR BUMPER ASSEMBLY

Hide 89342B 2.REMOVE REAR SIDE ULTRASONIC SENSOR (w/ Simple Intelligent Parking Assist System)

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E426487

Disconnect the connector.


b.
E426488

Disengage the claws to remove the rear side ultrasonic sensor.


Hide 89342 3.REMOVE REAR CORNER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E426490

Disconnect the connector.


b.
E426491

Disengage the claws to remove the rear corner ultrasonic sensor.


Hide 89342A 4.REMOVE REAR CENTER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E426493

Disconnect the connector.


b.
E426494

Disengage the claws to remove the rear center ultrasonic sensor.


Hide 89348T 5.REMOVE REAR SIDE ULTRASONIC SENSOR RETAINER (w/ Simple Intelligent Parking Assist System)

HINT:
·

Perform this procedure only when replacement of the rear side ultrasonic sensor retainer is necessary.

·

When removing the rear side ultrasonic sensor retainer, heat the rear bumper assembly and rear side ultrasonic sensor retainer using a heat light.



a.

Heat the rear bumper assembly and rear side ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Side Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.

Remove the rear side ultrasonic sensor retainer.

E426489C01
0.417,0 3.167,1.75 2.75,1.75 3.917,0 6.667,1.75 2.75,1.75 0.5,0.042 0.75,0.281 0.25,0.24 12 true *A 4,0.052 4.25,0.292 0.25,0.24 12 true *B
*A for LH Side *B for RH Side



Hide 52164A 6.REMOVE REAR BUMPER PLATE LH

HINT:

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR BUMPER>DISASSEMBLY


Hide 52163A 7.REMOVE REAR BUMPER PLATE RH

HINT:
·

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

·

The following procedure is for the LH side.



Hide 89348R 8.REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

·

When removing the rear corner ultrasonic sensor retainer, heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Corner Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.
E426492

Remove the rear corner ultrasonic sensor retainer.


Hide 89348S 9.REMOVE REAR CENTER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.

·

When removing the rear center ultrasonic sensor retainer, heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Center Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.
E426495

Remove the rear center ultrasonic sensor retainer.