Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2019.09
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1417  High Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the +BS terminal voltage deviates due to a malfunction in a power supply or charging system circuit such as the battery or alternator circuit, etc.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1417 High Power Supply Voltage Malfunction +BS terminal voltage is more than 16.5 V for 1 second or more.
·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of the skid control ECU (brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V



Result:
Result Proceed to
OK A
NG (for 8NR-FTS) B
NG (for 3ZR-FAE) C



A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE (+BS) TERMINAL)

B

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

C

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE (+BS) TERMINAL)
a.
C360727C64
1.479,0.146 1.885,0.406 0.406,0.26 0.51,1.771 0.677,1.073 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 1.542,0.188 1.875,0.385 0.333,0.198 10 false A42 0.208,1.698 0.938,1.896 0.729,0.198 10 false +BS
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-30 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE (IG1) TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE (IG1) TERMINAL)
a.
C360727C65
1.5,0.167 1.906,0.427 0.406,0.26 1.469,0.927 0.813,0.219 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 1.573,0.208 1.906,0.406 0.333,0.198 10 false A42 0.573,0.135 1.208,0.323 0.635,0.188 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-36 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C360727C05
0.063,0.302 0.5,0.552 0.438,0.25 2.427,0.313 2.771,0.958 true 0.135,0.063 0.448,0.26 0.313,0.198 10 false *a 0.146,0.333 0.458,0.531 0.313,0.198 10 false A42 2,0.229 2.5,0.438 0.5,0.208 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-46 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

5.RECONFIRM DTC
a.

Reconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1417 is not output. A
DTC C1417 is output. (for LHD) B
DTC C1417 is output. (for RHD) C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

C