Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2019.09
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the brake system warning light (red indicator) remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

The brake fluid level is insufficient.

·

The vacuum inside the brake booster decreases. (w/ Vacuum Warning Switch)

·

EBD operation is not possible.


WIRING DIAGRAM

C422960E01
0.792,1.198 1.188,1.396 0.396,0.198 10 false CANL 0.76,1.802 1.177,2 0.417,0.198 10 false CANH 0.917,4.656 1.208,4.844 0.292,0.188 10 false SW 0.844,6.292 1.188,6.479 0.344,0.188 10 false VCM 0.219,7.021 1.406,7.396 1.188,0.375 10 false Combination Meter Assembly 1.354,1.01 1.552,1.208 0.198,0.198 10 false 31 1.344,1.219 1.542,1.406 0.198,0.188 10 false F4 1.344,1.802 1.542,1.99 0.198,0.188 10 false F4 1.354,1.594 1.552,1.792 0.198,0.198 10 false 32 1.344,4.448 1.542,4.635 0.198,0.188 10 false 12 1.344,4.656 1.542,4.844 0.198,0.188 10 false F4 1.396,6.073 1.594,6.26 0.198,0.188 10 false 2 1.344,6.281 1.542,6.469 0.198,0.188 10 false F5 1.875,8.25 3.625,8.479 1.75,0.229 10 false : CAN Communication Line 2.854,2.271 3.635,2.49 0.781,0.219 10 false from Battery 2.281,2.948 3.625,3.146 1.344,0.198 10 false from IG1-NO. 1 Relay 4.385,2.438 5.125,2.656 0.74,0.219 10 false ABS-MAIN 4.229,3.135 5.24,3.333 1.01,0.198 10 false ECU-IG1 NO. 2 5.75,1.063 5.979,1.26 0.229,0.198 10 false 19 5.802,1.656 6.031,1.854 0.229,0.198 10 false 5 5.75,2.208 5.979,2.406 0.229,0.198 10 false 30 5.76,2.875 5.99,3.073 0.229,0.198 10 false 36 5.76,3.75 5.99,3.948 0.229,0.198 10 false 46 6.01,1.219 6.406,1.417 0.396,0.198 10 false CANL 6.01,1.813 6.427,2.01 0.417,0.198 10 false CANH 6.01,2.302 6.427,2.5 0.417,0.198 10 false +BS 6.021,2.958 6.438,3.156 0.417,0.198 10 false IG1 6.021,3.844 6.438,4.042 0.417,0.198 10 false GND1 5.604,4.719 7.125,5.135 1.521,0.417 10 false Skid Control ECU (Brake Actuator Assembly) 5.615,4.542 5.896,4.75 0.281,0.208 10 false A42 1.969,4.552 2.167,4.74 0.198,0.188 10 false 1 3.167,4.542 3.365,4.729 0.198,0.188 10 false 2 2.146,4.563 2.344,4.75 0.198,0.188 10 false + 2.979,4.552 3.177,4.74 0.198,0.188 10 false E 1.583,5.125 3.646,5.635 2.063,0.51 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly) 1.594,4.969 1.875,5.167 0.281,0.198 10 false A60 1.969,6.198 2.167,6.385 0.198,0.188 10 false 2 3.177,6.198 3.375,6.385 0.198,0.188 10 false 1 2.135,6.208 2.333,6.396 0.198,0.188 10 false + 2.979,6.198 3.177,6.385 0.198,0.188 10 false E 1.844,6.906 3.417,7.417 1.573,0.51 10 false Vacuum Warning Switch Assembly*1 1.844,6.74 2.125,6.927 0.281,0.188 10 false A31 4.26,8.125 6.542,8.365 2.281,0.24 10 false *1: w/ Vacuum Warning Switch

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V



Result:
Result Proceed to
OK A
NG (for 8NR-FTS) B
NG (for 3ZR-FAE) C



A

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE (+BS) TERMINAL)

B

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

C

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE (+BS) TERMINAL)
a.
C360727C64
1.479,0.146 1.885,0.406 0.406,0.26 0.51,1.771 0.677,1.073 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 1.542,0.188 1.875,0.385 0.333,0.198 10 false A42 0.208,1.698 0.938,1.896 0.729,0.198 10 false +BS
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-30 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE (IG1) TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE (IG1) TERMINAL)
a.
C360727C65
1.5,0.167 1.906,0.427 0.406,0.26 1.469,0.927 0.813,0.219 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 1.573,0.208 1.906,0.406 0.333,0.198 10 false A42 0.573,0.135 1.208,0.323 0.635,0.188 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the skid control ECU (brake actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A42-36 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

6.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C360727C05
0.063,0.302 0.5,0.552 0.438,0.25 2.427,0.313 2.771,0.958 true 0.135,0.063 0.448,0.26 0.313,0.198 10 false *a 0.146,0.333 0.458,0.531 0.313,0.198 10 false A42 2,0.229 2.5,0.438 0.5,0.208 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-46 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT BRAKE FLUID LEVEL WARNING SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

7.INSPECT BRAKE FLUID LEVEL WARNING SWITCH
a.
C304973C02
2.385,2.74 2.042,1.813 true 1.104,2.74 1.427,1.833 true 0.271,0.25 0.583,0.448 0.313,0.198 10 false *a 1.031,2.802 1.344,3 0.313,0.198 10 false E 2.365,2.802 2.677,3 0.313,0.198 10 false +
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly))


Turn the ignition switch off.


b.

Remove the reservoir filler cap and strainer.


c.

Disconnect the A60 brake fluid level warning switch connector.


d.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position changes according to the brake fluid level.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (+) - 2 (E) Switch OFF (Float up) 1.9 to 2.1 kΩ
1 (+) - 2 (E) Switch ON (Float down) Below 1 Ω


HINT:

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH)

B

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

C

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH)
a.

Disconnect the F4 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-12 (SW) - A60-1 (+) Always Below 1 Ω
F4-12 (SW) or A60-1 (+) - Body ground Always 10 kΩ or higher
A60-2 (E) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (w/ Vacuum Warning Switch) A
OK (w/o Vacuum Warning Switch) B
NG C



A

9.INSPECT VACUUM WARNING SWITCH ASSEMBLY

B

10.CHECK HARNESS AND CONNECTOR (BRAKE WARNING LIGHT CIRCUIT)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT VACUUM WARNING SWITCH ASSEMBLY
a.

Inspect the vacuum warning switch assembly.

For LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM WARNING SWITCH (for LHD)>ON-VEHICLE INSPECTION

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM WARNING SWITCH (for RHD)>ON-VEHICLE INSPECTION

OK:

The vacuum warning switch assembly is normal.


Result:
Proceed to
OK
NG




OK

10.CHECK HARNESS AND CONNECTOR (BRAKE WARNING LIGHT CIRCUIT)

NG

REPLACE VACUUM WARNING SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (BRAKE WARNING LIGHT CIRCUIT)
a.

Disconnect the F5 combination meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F5-2 (VCM) - A31-2 (+) Always Below 1 Ω
F5-2 (VCM) or A31-2 (+) - Body ground Always 10 kΩ or higher
A31-1 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

11.READ VALUE USING GTS (BRAKE WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.READ VALUE USING GTS (BRAKE WARNING LIGHT)
a.

Reconnect the A41 skid control ECU (brake actuator assembly) connector.


b.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Warning Light Brake system warning light (red indicator) ON or OFF ON: Warning light on
OFF: Warning light off
-
Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display
Brake Warning Light
50003 105 52

c.

Check the GTS display condition of the brake system warning light (red indicator).


Result:
Result Proceed to
ON is displayed. (for LHD) A
ON is displayed. (for RHD) B
OFF is displayed. C



A

B

C