Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2019.09–2020.08
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Clearance Warning ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Clearance Warning ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Clearance Warning (Clearance Sonar)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Clearance Warning (Clearance Sonar)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Clearance Warning (Clearance Sonar)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Clearance Warning ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Clearance warning ECU assembly branch line or connector

·

Power source circuit of clearance warning ECU assembly

·

Clearance warning ECU assembly ground circuit

·

Clearance warning ECU assembly



WIRING DIAGRAM

for TMMT Made


C366176E17
1.615,0.521 1.771,0.719 0.156,0.198 10 false 1 1.615,1.083 1.948,1.281 0.333,0.198 10 false 12 0.198,1.552 0.615,1.719 0.417,0.167 10 false F112 0.198,1.708 2.156,1.906 1.958,0.198 10 false No. 1 CAN Junction Connector 5.521,0.531 5.75,0.708 0.229,0.177 10 false 17 5.51,1.063 5.844,1.26 0.333,0.198 10 false 18 5.781,0.635 6.115,0.833 0.333,0.198 10 false R1 5.792,1.177 6.125,1.375 0.333,0.198 10 false R2 5.792,2.24 6.125,2.438 0.333,0.198 10 false IG 5.802,2.771 6.135,2.969 0.333,0.198 10 false E 5.469,3.167 5.896,3.375 0.427,0.208 10 false F142 5.458,3.344 6.969,3.74 1.51,0.396 10 false Clearance Warning ECU Assembly 4.333,2.385 5.354,2.583 1.021,0.198 10 false ECU-IG1 NO. 4 2.198,2.208 3.542,2.427 1.344,0.219 10 false from IG1-NO. 1 Relay 5.594,2.125 5.927,2.323 0.333,0.198 10 false 1 5.521,2.656 5.854,2.854 0.333,0.198 10 false 28


for TMC Made


C366176E18
1.615,0.521 1.771,0.719 0.156,0.198 10 false 1 1.625,1.083 1.958,1.281 0.333,0.198 10 false 7 0.198,1.552 0.615,1.719 0.417,0.167 10 false F164 0.198,1.708 2.156,1.906 1.958,0.198 10 false No. 1 CAN Junction Connector 5.521,0.531 5.75,0.708 0.229,0.177 10 false 17 5.51,1.063 5.844,1.26 0.333,0.198 10 false 18 5.781,0.635 6.115,0.833 0.333,0.198 10 false R1 5.792,1.177 6.125,1.375 0.333,0.198 10 false R2 5.792,2.24 6.125,2.438 0.333,0.198 10 false IG 5.802,2.771 6.135,2.969 0.333,0.198 10 false E 5.469,3.167 5.896,3.375 0.427,0.208 10 false F142 5.458,3.344 6.969,3.74 1.51,0.396 10 false Clearance Warning ECU Assembly 4.333,2.385 5.354,2.583 1.021,0.198 10 false ECU-IG1 NO. 4 2.198,2.208 3.542,2.427 1.344,0.219 10 false from IG1-NO. 1 Relay 5.594,2.125 5.927,2.323 0.333,0.198 10 false 1 5.521,2.656 5.854,2.854 0.333,0.198 10 false 28


CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait at least approximately 9 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (CLEARANCE WARNING ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the clearance warning ECU assembly connector.


c.
C380493C59
1.417,0.417 1.917,0.667 0.5,0.25 2.542,1.781 2.813,1.167 true 3.063,1.792 2.948,1.198 true 1.531,0.458 1.99,0.656 0.458,0.198 10 false F142 2.427,1.813 2.885,2.01 0.458,0.198 10 false R1 3.01,1.823 3.333,2.031 0.323,0.208 10 false R2 0.135,0.094 0.594,0.292 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F142-17 (R1) - F142-18 (R2) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C380493C60
1.5,0.25 2,0.5 0.5,0.25 0.833,1.833 0.49,1.188 true 1.781,1.823 1.563,1.354 true 1.604,0.292 2.063,0.49 0.458,0.198 10 false F142 0.792,1.854 1.25,2.052 0.458,0.198 10 false IG 1.75,1.854 2.208,2.052 0.458,0.198 10 false E 0.135,0.094 0.594,0.292 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F142-28 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F142-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)