Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2019.09–2020.08
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Radio Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Radio Receiver Assembly Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Display and Navigation (AVN)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Display and Navigation (AVN)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Display and Navigation (AVN)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Radio Receiver Assembly Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Radio and display receiver assembly branch line or connector

·

Power source circuit of radio and display receiver assembly

·

Radio and display receiver assembly ground circuit

·

Radio and display receiver assembly



WIRING DIAGRAM

C369875E05
0.083,1.729 2.188,1.979 2.104,0.25 10 false No. 3 CAN Junction Connector 0.083,1.563 0.698,1.771 0.615,0.208 10 false F114 1.646,1.063 2.26,1.271 0.615,0.208 10 false 20 1.646,0.521 2.26,0.729 0.615,0.208 10 false 9 5.396,1.146 5.885,1.333 0.49,0.188 10 false F131 5.396,0.615 5.885,0.792 0.49,0.177 10 false F131 5.396,2.229 5.917,2.406 0.521,0.177 10 false F131 5.396,2.76 5.854,2.948 0.458,0.188 10 false F129 5.396,3.302 5.896,3.479 0.5,0.177 10 false F129 5.396,3.844 6.01,4.01 0.615,0.167 10 false F129 5.479,0.438 5.938,0.615 0.458,0.177 10 false 13 5.479,0.969 5.771,1.156 0.292,0.188 10 false 14 5.469,2.031 5.802,2.219 0.333,0.188 10 false 19 5.49,2.573 5.792,2.771 0.302,0.198 10 false 15 5.521,3.104 5.823,3.333 0.302,0.229 10 false 4 5.49,3.646 5.833,3.865 0.344,0.219 10 false 1 5.802,0.625 6.313,0.875 0.51,0.25 10 false CANH 5.802,1.146 6.49,1.365 0.688,0.219 10 false CANL 5.802,2.229 6.208,2.469 0.406,0.24 10 false IG 5.802,2.771 6.344,3.021 0.542,0.25 10 false ACC1 5.802,3.302 6.302,3.521 0.5,0.219 10 false +B1 5.802,3.844 6.521,4.042 0.719,0.198 10 false GND1 5.302,4.229 7.042,4.719 1.74,0.49 10 false Radio and Display Receiver Assembly 4.573,3.438 5.292,3.635 0.719,0.198 10 false RADIO 4.469,2.906 5.25,3.104 0.781,0.198 10 false ECU-ACC 4.292,2.375 5.365,2.594 1.073,0.219 10 false ECU-IG1 NO. 4 2.177,2.219 4.052,2.427 1.875,0.208 10 false from IG1-NO. 1 Relay 2.5,2.75 4.375,2.958 1.875,0.208 10 false from ACC Relay 2.729,3.292 4.604,3.5 1.875,0.208 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch ON and wait at least approximately 30 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the radio and display receiver assembly connector.


c.
C387555C06
1.417,0.167 1.917,0.417 0.5,0.25 1.813,1.188 1.448,1.74 true 1.917,1.188 2.198,1.75 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.51,0.208 1.885,0.396 0.375,0.188 10 false F131 1.177,1.781 1.708,2.01 0.531,0.229 10 false CANH 2.063,1.792 2.594,2.021 0.531,0.229 10 false CANL
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-13 (CANH) - F131-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the radio and display receiver assembly connector.


b.
C387552C11
1.448,2.5 1.948,2.75 0.5,0.25 1.448,0.479 1.948,0.729 0.5,0.25 1.063,1.292 0.813,1.958 true 2.656,1.958 2.406,1.292 true 1.052,3.563 0.844,3.979 true 2.302,1.427 1.99,1.969 true 0.167,0.156 0.479,0.313 0.313,0.156 10 false *a 1.542,0.521 1.958,0.688 0.417,0.167 10 false F129 1.552,2.542 1.969,2.708 0.417,0.167 10 false F131 0.615,1.969 1.115,2.219 0.5,0.25 10 false GND1 2.552,1.979 2.969,2.229 0.417,0.25 10 false +B1 0.771,4 1.26,4.24 0.49,0.24 10 false IG 1.823,1.99 2.323,2.24 0.5,0.25 10 false ACC1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F129-1 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F129-4 (+B1) - Body ground Always 11 to 14 V
F129-15 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
F131-19 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)