Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2019.09
RM32H0E _53 Suspension _059606 TIRE PRESSURE MONITORING _0292310 TIRE PRESSURE WARNING SYSTEM D

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  INITIALIZATION  


NOTICE:
·

Initialization can be confirmed through the tire pressure warning light.

·

If the ignition switch is turned off during initialization, the tire pressure warning ECU and receiver memorizes that initialization was being performed. Therefore, it is not necessary to perform the initialization procedure again after turning the ignition switch to ON.

·

The order in which the data is received is random.

·

If the signals from all the tire pressure warning valve and transmitters are received, initialization is completed.

·

Initialization is completed when the Data List "ID Tire Inflation Pressure" display shows the correct pressures.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DATA LIST / ACTIVE TEST

·

Initialization is normally completed within a few minutes. However, it may take 10 minutes or more until the tire pressure of the tire inflation pressure display function is shown.

·

It may take a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121 to C2124 (C2125: w/ Full Size Spare Tire).

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>C2121

·

If initialization has not been completed successfully, DTC C2177 is stored after a vehicle speed of 40 km/h (25 mph) or more is detected for 20 minutes or more.

·

During test mode (sensor check mode), the system will not change to initialization mode even if the initialization procedure is performed.

·

ID Switching Function:

While the answer-back function for the ID switching function is operating, the system will not change to initialization mode even if the initialization procedure is performed.

·
C217594C07
1.781,1.458 2.052,1.76 true 1.573,1.073 1.365,1.76 true 0.156,0.083 0.833,0.365 0.677,0.281 10 false *a 1.969,1.792 2.49,1.969 0.521,0.177 10 false TC 1.198,1.792 1.552,1.969 0.354,0.177 10 false CG
*a Front view of DLC3


Initialization can be terminated by connecting terminals 13 (TC) and 4 (CG) of the DLC3. (for 3ZR-FAE)



BEFORE INITIALIZATION


a.

Set the tire pressure to the specified value.

NOTICE:

Refer to the link as the procedure for adjusting the tire pressures differs depending on the temperature of the tires.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION




INITIALIZATION PROCEDURE


HINT:

The tire pressure warning system illuminates the tire pressure warning light to warn the driver when any of the following conditions are met:

·

Due to the operation of the steering pad switch assembly, the tire pressure drops to approximately 80% or less of the tire pressure set during system initialization.

·

The tire pressure drastically decreases (approximately 20 kPa (0.2 kgf/cm2, 2.9 psi) or more within several minutes) to approximately 80% or less of the tire pressure* when the tires are warmed.

*: If initialization is performed and the vehicle is driven for a certain period of time, the tire pressure set during system initialization is adjusted and set to the tire pressure when the tires are warmed from the driving conditions.

NOTICE:

If the tire pressure is decreased approximately 20 kPa (0.2 kgf/cm2, 2.9 psi) or more in order to adjust the tire pressure, even if the adjusted tire pressure is 80% or more than the tire pressure set during system initialization, the tire pressure warning light may illuminate if the tire pressure drops below 80% of the tire pressure set when the tires are warmed. In this case, perform initialization again.




a.

Turn the ignition switch to ON.


b.
C367119C01
1.917,0.781 2.573,0.542 true 0.156,0.135 0.479,0.417 0.323,0.281 12 false *A 0.635,0.229 0.948,0.385 0.313,0.156 10 false *1 1.708,0.719 2.021,0.875 0.313,0.156 10 false *2 0.125,3.344 0.438,3.5 0.313,0.156 10 false *a 2.031,4.24 2.344,4.396 0.313,0.156 10 false *b 0.667,3.635 0.979,3.792 0.313,0.156 10 false *c 0.667,3.896 0.979,4.052 0.313,0.156 10 false *d 2.271,3.313 2.583,3.469 0.313,0.156 10 false *b
*A for LHD
*1 Tire Pressure Warning Light
*2 "ENTER" Switch (Steering Pad Switch Assembly)
*a Tire Pressure Warning Light Output Pattern
*b 1 sec.
*c ON
*d OFF


C367120C01
1.844,0.792 2.573,0.531 true 0.146,0.125 0.458,0.469 0.313,0.344 12 false *A 0.656,0.188 0.969,0.344 0.313,0.156 10 false *1 1.625,0.729 1.938,0.885 0.313,0.156 10 false *2 0.26,3.344 0.573,3.5 0.313,0.156 10 false *a 2.031,4.24 2.344,4.396 0.313,0.156 10 false *b 0.677,3.688 0.99,3.844 0.313,0.156 10 false *c 0.656,3.906 0.969,4.063 0.313,0.156 10 false *d 2.25,3.313 2.563,3.469 0.313,0.156 10 false *b
*A for RHD
*1 Tire Pressure Warning Light
*2 "ENTER" Switch (Steering Pad Switch Assembly)
*a Tire Pressure Warning Light Output Pattern
*b 1 sec.
*c ON
*d OFF


Operate the steering pad switch assembly, select "TPMS" on the multi-information display and press and hold the "ENTER" switch (steering pad switch assembly) until the tire pressure warning light blinks 3 times.


c.

Turn the ignition switch off.


d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 2 Tire Inflation Pressure ID2 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 3 Tire Inflation Pressure ID3 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 4 Tire Inflation Pressure ID4 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 5 Tire Inflation Pressure ID5 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure
·

If N/A is displayed, data has not been received.*1

·

*2


HINT:
·

*1: It may take a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121 to C2124 (C2125: w/ Full Size Spare Tire).

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>C2121

·

*2: w/ Full Size Spare Tire




g.

Check that initialization has been completed.


h.

Confirm that the tire pressure data of all tires is displayed on the GTS screen.