Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2019.09
RM32H0E _53 Suspension _059606 TIRE PRESSURE MONITORING _0292310 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2121  No Signal from Transmitter ID1  C2122  No Signal from Transmitter ID2  C2123  No Signal from Transmitter ID3  C2124  No Signal from Transmitter ID4  C2125  No Signal from Transmitter ID5  C2181  Transmitter ID1 not Received (Test Mode DTC)  C2182  Transmitter ID2 not Received (Test Mode DTC)  C2183  Transmitter ID3 not Received (Test Mode DTC)  C2184  Transmitter ID4 not Received (Test Mode DTC)  C2185  Transmitter ID5 not Received (Test Mode DTC)  


DESCRIPTION

The tire pressure warning valve and transmitters that are installed in the tire and wheel assemblies measure the tire pressure of each wheel. The measured values are transmitted to the tire pressure warning ECU and receiver in the vehicle as radio waves. The ECU compares the measured tire pressure values with the tire pressure threshold. When the measured tire pressure value is less than this threshold, the warning light in the combination meter assembly illuminates.

The tire pressure warning valve and transmitters constantly send radio waves to the tire pressure warning ECU and receiver.

Under the conditions below, the tire pressure warning ECU and receiver is unable to receive the signals from the tire pressure warning valve and transmitters, and a DTC is stored.

·

Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

·

Devices using similar radio frequencies are used in the vehicle.

·

The ID of a tire pressure warning valve and transmitter is mistyped during registration.

·

A tire, wheel and/or transmitter from a different vehicle is installed.


HINT:

When no transmitter ID is received from a tire pressure warning valve and transmitter for 10 minutes or more while the vehicle speed is more than 40 km/h (25 mph), or no transmitter ID is received from all of the tire pressure warning valve and transmitters for 10 minutes or more, DTCs from C2121 to C2124 (C2125: w/ Full Size Spare Tire) are stored.

DTCs C2121 to C2124 (C2125: w/ Full Size Spare Tire) can only be cleared by using the GTS. DTCs C2181 to C2184 (C2185: w/ Full Size Spare Tire) can be cleared when the tire pressure warning valve and transmitter sends a forced transmission signal or test mode ends. DTCs C2181 to C2184 (C2185: w/ Full Size Spare Tire) are output only in test mode.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
C2121 No Signal from Transmitter ID1 Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

Any transmitter ID is not received from tire pressure warning valve and transmitters.

·

Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 10 minutes or more.


(b) When both conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

No transmitter ID is received from tire pressure warning valve and transmitters for 10 minutes or more.


·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2122 No Signal from Transmitter ID2 Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

Any transmitter ID is not received from tire pressure warning valve and transmitters.

·

Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 10 minutes or more.


(b) When both conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

No transmitter ID is received from tire pressure warning valve and transmitters for 10 minutes or more.


·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2123 No Signal from Transmitter ID3 Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

Any transmitter ID is not received from tire pressure warning valve and transmitters.

·

Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 10 minutes or more.


(b) When both conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

No transmitter ID is received from tire pressure warning valve and transmitters for 10 minutes or more.


·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2124 No Signal from Transmitter ID4 Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

Any transmitter ID is not received from tire pressure warning valve and transmitters.

·

Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 10 minutes or more.


(b) When both conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

No transmitter ID is received from tire pressure warning valve and transmitters for 10 minutes or more.


·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2125 No Signal from Transmitter ID5 Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

Any transmitter ID is not received from tire pressure warning valve and transmitters.

·

Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 10 minutes or more.


(b) When both conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

No transmitter ID is received from tire pressure warning valve and transmitters for 10 minutes or more.


·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


w/ Full Size Spare Tire
C2181 Transmitter ID1 not Received (Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2182 Transmitter ID2 not Received (Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2183 Transmitter ID3 not Received (Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2184 Transmitter ID4 not Received (Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2185 Transmitter ID5 not Received (Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


w/ Full Size Spare Tire

NOTICE:
·

ID Switching Function:

(Main) is displayed on the DTC screen for the DTCs even when the 2nd set of tires is selected.

·

When DTCs C2121 to C2124 (C2125: w/ Full Size Spare Tire) are set, DTC C2179 may be set simultaneously. In such cases, troubleshoot DTCs C2121 to C2124 (C2125: w/ Full Size Spare Tire) first, then troubleshoot DTC C2179.



HINT:

It is necessary to perform the following procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.


WIRING DIAGRAM

C353322E13
3.177,0.146 4.573,0.542 1.396,0.396 10 false Tire Pressure Warning Valve and Transmitter 3.167,1.188 4.563,1.583 1.396,0.396 10 false Tire Pressure Warning Valve and Transmitter 3.177,2.198 4.625,2.573 1.448,0.375 10 false Tire Pressure Warning Valve and Transmitter* 0.646,1.646 2.042,2.042 1.396,0.396 10 false Tire Pressure Warning Valve and Transmitter 0.656,0.625 2.052,1.021 1.396,0.396 10 false Tire Pressure Warning Valve and Transmitter 5.76,2.958 6,3.156 0.24,0.198 10 false 4 3.625,2.958 3.865,3.156 0.24,0.198 10 false 4 3.615,3.427 3.854,3.625 0.24,0.198 10 false 5 5.76,3.427 6,3.625 0.24,0.198 10 false 5 5.969,3.052 6.385,3.281 0.417,0.229 10 false RDA 3.188,3.063 3.604,3.292 0.417,0.229 10 false RDA 3.188,3.479 3.604,3.708 0.417,0.229 10 false PRG 5.979,3.521 6.396,3.75 0.417,0.229 10 false PRG 1.292,3.031 2.938,3.406 1.646,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 1.01,3.031 1.427,3.26 0.417,0.229 10 false F15 3.99,5.021 5.24,5.406 1.25,0.385 10 false Combination Meter Assembly 3.99,4.865 4.406,5.094 0.417,0.229 10 false F4 5.969,4.208 6.417,4.448 0.448,0.24 10 false CLSW 5.74,4.094 5.979,4.292 0.24,0.198 10 false 3 3.99,4.104 4.229,4.302 0.24,0.198 10 false 4 3.625,4.198 4.042,4.427 0.417,0.229 10 false INT 2.604,4.063 3.531,4.427 0.927,0.365 10 false Tire Pressure Warning Light 2.573,4.49 2.99,4.719 0.417,0.229 10 false ET 2.573,4.958 2.99,5.188 0.417,0.229 10 false MSSL 2.573,5.375 3.094,5.625 0.521,0.25 10 false MSM+ 2.281,4.385 2.521,4.583 0.24,0.198 10 false 21 2.313,4.854 2.552,5.052 0.24,0.198 10 false 33 2.323,5.271 2.563,5.469 0.24,0.198 10 false 28 5.979,5.885 6.427,6.125 0.448,0.24 10 false GND 5.688,5.771 6.104,6 0.417,0.229 10 false 12 2.219,6.125 2.635,6.354 0.417,0.229 10 false F29 3.656,6.094 4.073,6.323 0.417,0.229 10 false z1 2.646,6.854 3.167,7.104 0.521,0.25 10 false EAU 2.615,6.458 3.135,6.708 0.521,0.25 10 false +DP2 2.667,6.073 3.188,6.323 0.521,0.25 10 false +DP 2.24,5.938 2.479,6.135 0.24,0.198 10 false 10 2.25,6.375 2.49,6.573 0.24,0.198 10 false 11 2.302,6.771 2.542,6.969 0.24,0.198 10 false 3 3.688,5.917 3.927,6.115 0.24,0.198 10 false 2 3.698,6.344 3.938,6.542 0.24,0.198 10 false 3 3.698,6.75 3.938,6.948 0.24,0.198 10 false 8 2.51,7.302 3.615,7.698 1.104,0.396 10 false Spiral Cable Sub-assembly 3.917,7.333 5.198,7.74 1.281,0.406 10 false Steering Pad Switch Assembly 0.74,7.01 1.156,7.24 0.417,0.229 10 false F144 1.094,7.01 1.615,7.26 0.521,0.25 10 false DLC3 0.583,7.479 1.74,7.667 1.156,0.188 10 false : Radio Waves 0.583,7.771 2.333,7.979 1.75,0.208 10 false : CAN Communication Line 5.604,6.5 6.021,6.729 0.417,0.229 10 false M23 5.604,6.688 6.99,7.073 1.385,0.385 10 false Tire Pressure Warning ECU and Receiver 0.167,8.094 1.917,8.302 1.75,0.208 10 false *: w/ Full Size Spare Tire 3.656,6.51 4.073,6.74 0.417,0.229 10 false z1 3.656,6.917 4.073,7.146 0.417,0.229 10 false z1 2.229,6.542 2.646,6.771 0.417,0.229 10 false F29 2.229,6.938 2.646,7.167 0.417,0.229 10 false F29

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.



PROCEDURE

1.CHECK FREQUENCY RECEIVING CONDITION
a.

Check that the following conditions are not met:

i.

Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

HINT:

If the vehicle is located in an area such as the one described above, the tire pressure warning light may illuminate after blinking 1 minute due to interfering radio frequencies.



ii.

Devices using similar radio frequencies are used in the vehicle.

OK:

Facilities or devices that use similar radio frequencies are not located in the vicinity of the vehicle.


HINT:

Radio transmissions may be interrupted due to the surroundings or devices installed by the user.




Result:
Proceed to
OK
NG



OK

2.IDENTIFY TRANSMITTER CORRESPONDING TO DTC

NG

CHECK IF ANY DEVICE IS INSTALLED BY USER

2.IDENTIFY TRANSMITTER CORRESPONDING TO DTC
a.

Set the tire pressure to the specified value.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


g.

Display the "ID Tire Inflation Pressure" value for each wheel using the GTS.


h.

Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds. If the "ID Tire Inflation Pressure" value displayed on the GTS does not change, the tire pressure warning valve and transmitter corresponding to the unchanged "ID Tire Inflation Pressure" value was the cause of the output DTC.

HINT:
·

Identify the malfunctioning tire pressure warning valve and transmitter by repeatedly decreasing the tire pressure for each tire.

·

Record which "ID Tire Inflation Pressure" value corresponds to each tire.



Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 2 Tire Inflation Pressure ID2 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 3 Tire Inflation Pressure ID3 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 4 Tire Inflation Pressure ID4 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 5 Tire Inflation Pressure ID5 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure
·

If N/A is displayed, data has not been received.*1

·

*2


HINT:
·

*1: It may take a few minutes until the values are displayed.

·

*2: w/ Full Size Spare Tire



Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Tire Inflation Pressure
ID 2 Tire Inflation Pressure
ID 3 Tire Inflation Pressure
ID 4 Tire Inflation Pressure
ID 5 Tire Inflation Pressure
50003 203 36,37,38,39,40

i.

Check the Data List.

NOTICE:
·

It may take a few minutes to display the updated tire pressure data.

·

When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.

·

Record the transmitter IDs and positions of transmitters that are normal.




j.

After confirming that the "ID Tire Inflation Pressure" value for one tire has changed, repeat this procedure one by one. Identify the transmitter that corresponds to the DTC.


Result:
Result Proceed to
One or more transmitter is abnormal A
All transmitters are normal B



A

3.CHECK TRANSMITTER ID

B

END

3.CHECK TRANSMITTER ID
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

Check the values by referring to the table below.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Registered ID 1 Code Registered ID1 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID1 displayed -
Registered ID 2 Code Registered ID2 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID2 displayed -
Registered ID 3 Code Registered ID3 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID3 displayed -
Registered ID 4 Code Registered ID4 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID4 displayed -
Registered ID 5 Code Registered ID5 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID5 displayed *2
HINT:
·

*1: Displayed only when the ID No. is not registered.

·

*2: w/ Full Size Spare Tire

·

The wheel position cannot be determined from ID1 through ID4 (ID5: Full Size Spare Tire) on the Data List.



Chassis > Tire Pressure Monitor > Data List
Tester Display
Registered ID 1 Code
Registered ID 2 Code
Registered ID 3 Code
Registered ID 4 Code
Registered ID 5 Code
50003 203 7,8,9,10,11

g.

Check the ID number on the identified transmitter by removing it from the tire and wheel.

C353321C01
6.031,1.313 6.156,0.719 6.156,0.719 6.302,0.719 false 0.271,0.229 0.583,0.427 0.313,0.198 10 false *1 6.354,0.656 6.667,0.854 0.313,0.198 10 false *a
*1 Tire Pressure Warning Valve and Transmitter - -
*a Transmitter ID (7-digit Number) - -



h.

Confirm that the ID number on the transmitter and recorded transmitter ID match.


Result:
Result Proceed to
Match A
Do not match B



A

4.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER

B

5.REGISTRATION OF TRANSMITTER ID
4.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER
a.

Replace the tire pressure warning valve and transmitter.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.REGISTRATION OF TRANSMITTER ID
5.REGISTRATION OF TRANSMITTER ID

Result:
Proceed to
NEXT



NEXT

6.PERFORM INITIALIZATION
6.PERFORM INITIALIZATION

Result:
Proceed to
NEXT



NEXT

7.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
7.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

Check the values by referring to the table below.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 2 Tire Inflation Pressure ID2 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 3 Tire Inflation Pressure ID3 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 4 Tire Inflation Pressure ID4 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 5 Tire Inflation Pressure ID5 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure
·

If N/A is displayed, data has not been received.*1

·

*2


HINT:
·

*1: It may take a few minutes until the values are displayed.

·

When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.

·

*2: w/ Full Size Spare Tire

·

The wheel position cannot be determined from ID1 through ID4 (ID5: Full Size Spare Tire) on the Data List.



Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Tire Inflation Pressure
ID 2 Tire Inflation Pressure
ID 3 Tire Inflation Pressure
ID 4 Tire Inflation Pressure
ID 5 Tire Inflation Pressure
50003 203 36,37,38,39,40

Result:
Result Proceed to
Tire pressure values are not displayed. A
All tire pressure readings are equal to specified values. B



A

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

B

END