Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER › 2019.09–2020.12
RM32H0E _59 Vehicle Exterior _060783 EXTERIOR PANELS / TRIM _0298065 REAR BUMPER A

EXTERIOR PANELS / TRIM  REAR BUMPER  REASSEMBLY  


PROCEDURE

Hide 52023 1.INSTALL REAR BUMPER REINFORCEMENT SUB-ASSEMBLY

a.
B458637

Install the rear bumper reinforcement sub-assembly with the 8 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 52563A 2.INSTALL REAR BUMPER UPPER RETAINER LH

a.
B560328

Install the rear bumper upper retainer LH with screw.


Hide 52562B 3.INSTALL REAR BUMPER UPPER RETAINER RH

HINT:

Use the same procedure as for the LH side.


Hide 5.INSTALL REAR COMBINATION LIGHT RH

HINT:

Use the same procedure as for the LH side.


Hide 81498 7.INSTALL REAR COMBINATION LIGHT COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 52576B 8.INSTALL REAR BUMPER SIDE RETAINER LH

a.
B474042C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the claw and guide to install rear bumper side retainer LH as shown in the illustration.


b.
B474036

Install the 2 screws.


Hide 52575 9.INSTALL REAR BUMPER SIDE RETAINER RH

HINT:

Use the same procedure as for the LH side.


Hide 52453 10.INSTALL REAR BUMPER CENTER GUARD

a.

Engage the claws and guides to install the rear bumper center guard.

B458632


b.

Install the 2 clips and 6 outside moulding retainers.

B458631C01
1.458,0.927 1.667,1.125 0.208,0.198 10 true *b 1.042,1.396 1.292,1.563 0.25,0.167 10 true *b 0.531,1.542 0.74,1.719 0.208,0.177 10 true *b 0.479,2.156 0.698,2.365 0.219,0.208 10 true *a 5.552,0.979 5.76,1.177 0.208,0.198 10 true *b 6.021,1.385 6.229,1.583 0.208,0.198 10 true *b 6.51,1.552 6.719,1.75 0.208,0.198 10 true *b 6.615,2.063 6.833,2.271 0.219,0.208 10 true *a
*a Clip *b Outside Moulding Retainer



Hide 52154B 11.INSTALL REAR BUMPER SIDE STAY LH

a.
B557796C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw to install the rear bumper side stay LH as shown in the illustration.


b.

Install the clip and screw.


Hide 52153A 12.INSTALL REAR BUMPER SIDE STAY RH

HINT:

Use the same procedure as for the LH side.


Hide 52463 13.INSTALL REAR BUMPER PAD LH

HINT:

When installing the rear bumper pad LH, heat the rear bumper assembly using a heat light.


Heating Temperature
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper assembly excessively.


a.

Clean the rear bumper assembly surface.

i.

Using a heat light, heat the rear bumper assembly surface.


ii.

Remove the double-sided tape from the rear bumper assembly.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Remove the release paper from a new rear bumper pad LH.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B458904C01
1.125,1.552 1.542,1.24 true 0.896,1.5 1.125,1.729 0.229,0.229 10 true *a
*a Scribed Line


Install the rear bumper pad LH as shown in the illustration.

HINT:

Install the rear bumper pad LH along the scribed line on the rear bumper cover.



Hide 52462 14.INSTALL REAR BUMPER PAD RH

HINT:

Use the same procedure as for the LH side.


Hide 52461F 15.INSTALL REAR BUMPER PAD

HINT:

When installing the rear bumper pad, heat the rear bumper assembly using a heat light.


Heating Temperature
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper assembly excessively.


a.

Clean the rear bumper assembly surface.

i.

Using a heat light, heat the rear bumper assembly surface.


ii.

Remove the double-sided tape from the rear bumper assembly.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Remove the release paper from a new rear bumper pad.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B458644C01
1.177,0.729 1.531,0.906 true 0.854,0.604 1.094,0.813 0.24,0.208 10 true *a
*a Scribed Line


Install the rear bumper pad as shown in the illustration.

HINT:

Install the rear bumper pad along the scribed line on the rear bumper cover.



Hide 52162B 16.INSTALL NO. 1 REAR BUMPER PLATE

a.
B474028

Engage the hook to install the No. 1 rear bumper plate.


b.

Disengage the claws.


Hide 52164A 17.INSTALL REAR BUMPER PLATE LH

a.
B557797C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the rear bumper plate LH as shown in the illustration.


b.

Install the 2 screws.


Hide 52163A 18.INSTALL REAR BUMPER PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 81920 19.INSTALL REFLEX REFLECTOR ASSEMBLY LH

a.
B557798C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide and claw to install the reflex reflector assembly as shown in the illustration.


b.

Install the screw.


Hide 81910 20.INSTALL REFLEX REFLECTOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 52166A 21.INSTALL REAR BUMPER UPPER COVER LH

a.
B474041

Engage the hook to install the rear bumper upper cover LH.


Hide 52165A 22.INSTALL REAR BUMPER UPPER COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 82169A 23.INSTALL NO. 6 FLOOR WIRE (w/ Wire Harness)

a.

w/ TOYOTA Parking Assist-sensor System and Rear Fog Light:

i.

Engage the clamps to install the No. 6 floor wire.

B557788



b.

w/ Rear Fog Light:

i.

Engage the clamps to install the No. 6 floor wire.

B557790



c.

w/ TOYOTA Parking Assist-sensor System:

i.

Engage the clamps to install the No. 6 floor wire.

B557789



Hide 81481Q 24.INSTALL FOG LIGHT BRACKET (w/o LED Back-up Light and Rear Fog Light)

a.
B474025

Install the fog light bracket with the 2 screws.


Hide 81480B 25.INSTALL REAR FOG LIGHT ASSEMBLY (w/ Rear Fog Light)

Hide 26.INSTALL BACK UP LIGHT ASSEMBLY (w/ LED Back-up Light)

Hide 89348S 27.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89348R 28.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89348T 29.INSTALL REAR SIDE ULTRASONIC SENSOR RETAINER (w/ Simple Intelligent Parking Assist System)

Hide 89342A 30.INSTALL REAR CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89342 31.INSTALL REAR CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89342B 32.INSTALL REAR SIDE ULTRASONIC SENSOR (w/ Simple Intelligent Parking Assist System)