Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR WINDOW FRAME MOULDING › 2019.09–2020.08
RM32H0E _59 Vehicle Exterior _060783 EXTERIOR PANELS / TRIM _0298071 FRONT DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  FRONT DOOR WINDOW FRAME MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the front door window frame moulding removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Door glass run Initialize Power Window Control System
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 75720 2.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

Hide 75072A 3.REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY

HINT:

When removing the front door outside moulding sub-assembly, heat the vehicle body and front door outside moulding sub-assembly using a heat light.


Heating Temperature
Item Temperature
Front Door Outside Moulding Sub-assembly 40 to 60°C (104 to 140°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body or moulding excessively.


a.

Using a heat light, heat the front door outside moulding sub-assembly.


b.
B458696C01
1.813,1.458 2.073,1.75 true 2.146,1.646 2.458,1.802 0.313,0.156 10 false *a
*a Double-sided Tape
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)
V100155

Protective Tape


Apply protective tape around the front door outside moulding sub-assembly as shown in the illustration.


c.

Using a moulding remover D, disengage the clip and guide, and separate the double-sided tape and caulking sponge to remove the front door outside moulding sub-assembly as shown in the illustration.


Hide 67862 4.DISCONNECT FRONT DOOR WEATHERSTRIP

a.
B458695

Using a clip remover, disengage the clips to disconnect the front door weatherstrip.


Hide 67664 5.REMOVE DOOR FRAME UPPER GARNISH

Hide 68151C 6.REMOVE FRONT DOOR GLASS RUN

Hide 67402F 7.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

Hide 68126 8.REMOVE FRONT DOOR FIX WINDOW GLASS

Hide 75754A 9.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING

a.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


b.
B360296C07
0.542,0.906 0.833,1.219 false 0.875,1.156 1.188,1.313 0.313,0.156 10 false *a 0.333,1.5 0.49,1.698 0.156,0.198 10 false A
*a Tape


Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:
Area Measurement
A 5.0 mm (0.197 in.)


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



c.

Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 6 rivets.

B458697

CAUTION:

Be careful of the drilled rivets, as they may be hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Prying the rivets with the drill may damage the rivet installation holes or drill bit.




d.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.


e.

Disengage the guide to remove the front door upper window frame moulding from the door frame.


Hide 67914 10.REMOVE FRONT DOOR SCUFF PLATE

Hide 62112 11.REMOVE COWL SIDE TRIM BOARD

Hide 75752C 12.REMOVE FRONT DOOR FRONT WINDOW FRAME MOULDING

a.

Disconnect each connector.


b.

Disengage each clamp.


c.
B458698

Remove the 5 bolts and front door panel sub-assembly.

NOTICE:

To prevent damage, when removing the front door panel sub-assembly, make sure that there are enough people available to hold it securely.



d.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


e.
B360296C07
0.542,0.906 0.833,1.219 false 0.875,1.156 1.188,1.313 0.313,0.156 10 false *a 0.333,1.5 0.49,1.698 0.156,0.198 10 false A
*a Tape


Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:
Area Measurement
A 5.0 mm (0.197 in.)


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



f.

Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 2 rivets and front door front window frame moulding.

B458699

CAUTION:

Be careful of the drilled rivets, as they may be hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Prying the rivets with the drill may damage the rivet installation holes or drill bit.




g.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.