Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2019.09
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch signals and uses them to determine whether or not the brakes are applied.

The skid control ECU (brake actuator assembly) has a detection circuit that it uses to detect an open in the stop light input line.

If the skid control ECU (brake actuator assembly) detects an open in this circuit, it will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1425 Open in Stop Light Switch Circuit An open in the stop light switch input line continues for 3 seconds or more.
·

Wire harness or connector

·

Stop light switch assembly

·

Skid control ECU (brake actuator assembly)

·

Stop light circuit



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed.


Result:
Result Proceed to
All stop lights illuminate when the brake pedal is depressed and turn off when the brake pedal is released. A
All stop lights do not illuminate when the brake pedal is depressed. B
One or more stop lights illuminate when the brake pedal is depressed but remain on when the brake pedal is released. C



A

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

B

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - STOP LIGHT)

C

REPLACE STOP LIGHT SWITCH ASSEMBLY

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display
Stop Light SW
50003 105 37

d.

Check that the stop light switch display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT INSPECTION

NG

9.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)
3.STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT INSPECTION
a.
C401043C46
0.417,0.656 0.76,0.885 0.344,0.229 2.417,1.646 2.167,1.063 true 0.469,0.677 0.927,0.875 0.458,0.198 10 false A91 0.188,0.188 0.646,0.385 0.458,0.198 10 false *a 2.313,1.677 2.771,1.875 0.458,0.198 10 false OUT
*a Component with harness connected
(Stop Light Switch Assembly)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A91-1 (OUT) - Body ground
·

Ignition switch to ON

·

The headlights are on

·

The blower motor switch is in the HI position

·

The rear window defogger is turned on

·

Stop light switch assembly off (Brake pedal released)


1.5 V or less



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

6.CHECK STOP LIGHT SWITCH ASSEMBLY
4.CLEAR DTC
a.

Turn the ignition switch off.


b.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Clear DTCs
50002 105

Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Start the engine.


c.

Drive the vehicle and depress the brake pedal several times to test the stop light circuit.


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1249 is not output. A
DTC C1249 is output. (for LHD) B
DTC C1249 is output. (for RHD) C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

C

6.CHECK STOP LIGHT SWITCH ASSEMBLY
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.
C401044C54
0.49,0.646 0.833,0.854 0.344,0.208 1.26,1.25 1.115,1.677 true 0.25,0.198 0.563,0.354 0.313,0.156 10 false *a 0.542,0.667 1,0.885 0.458,0.219 10 false A91 0.979,1.708 1.396,1.906 0.417,0.198 10 false OUT
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A91 stop light switch assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A91-1 (OUT) - Body ground Stop light switch assembly off
(Brake pedal released)
1.5 V or less



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

7.CHECK BRAKE ACTUATOR ASSEMBLY
7.CHECK BRAKE ACTUATOR ASSEMBLY
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.
C401044C54
0.49,0.646 0.833,0.854 0.344,0.208 1.26,1.25 1.115,1.677 true 0.25,0.198 0.563,0.354 0.313,0.156 10 false *a 0.542,0.667 1,0.885 0.458,0.219 10 false A91 0.979,1.708 1.396,1.906 0.417,0.198 10 false OUT
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A91-1 (OUT) - Body ground Stop light switch assembly off
(Brake pedal released)
1.5 V or less



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

8.CHECK FOR SHORT TO +B IN STP2 CIRCUIT
8.CHECK FOR SHORT TO +B IN STP2 CIRCUIT
a.

Check that there is no short to +B in the STP2 circuit (wire harnesses, connectors and stop lights).

OK:

No short to +B.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE MALFUNCTIONING PART

9.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)
a.
C360727C06
0.063,0.281 0.51,0.531 0.448,0.25 2.802,0.375 2.448,0.938 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 0.146,0.323 0.49,0.542 0.344,0.219 10 false A42 2.854,0.26 3.281,0.448 0.427,0.188 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-44 (STP2) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V*


HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - STOP LIGHT)
a.

Check that there is no open in the wire harnesses and connectors from terminal OUT of the stop light switch assembly to the stop lights.


OK:

No open.


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR