Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2019.09–2020.08
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0297889 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly outputs a signal to the ECM. When the ECM receives the signal, it cancels control of vehicle speed by the dynamic radar cruise control system. The fail-safe function operates to enable normal operation even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake pedal is depressed, voltage is applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM turns the dynamic radar cruise control system off.

DTC No. Detection Item DTC Detection Condition Trouble Area
P057162 Brake Switch "A" Signal Compare Failure While the dynamic radar cruise control system is operating, voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for approximately 0.5 seconds or more.
·

Stop light switch assembly

·

Harness or connector

·

ECM



WIRING DIAGRAM

C367135E20
1.385,1.229 2,1.427 0.615,0.198 10 false STOP 1.188,1.729 2.25,2.021 1.063,0.292 10 false ECU-IG2 NO. 3 3.354,2.448 4.115,2.646 0.76,0.198 10 false A91 3.344,2.594 4.438,2.979 1.094,0.385 10 false Stop Light Switch Assembly 3.438,2.083 4.198,2.281 0.76,0.198 10 false GND 3.448,1.573 4.208,1.771 0.76,0.198 10 false B 3.448,1.073 4.208,1.271 0.76,0.198 10 false B 3.24,0.969 3.49,1.146 0.25,0.177 10 false 7 3.24,1.469 3.49,1.688 0.25,0.219 10 false 6 3.25,1.969 3.5,2.188 0.25,0.219 10 false 2 3.552,3.51 4.313,3.708 0.76,0.198 10 false STP 3.563,5 4.323,5.198 0.76,0.198 10 false STP 3.979,5.198 4.229,5.396 0.25,0.198 10 false *2 3.958,4.969 4.417,5.167 0.458,0.198 10 false F18 4.333,4.969 4.792,5.167 0.458,0.198 10 false F19 4.333,5.198 4.583,5.396 0.25,0.198 10 false *1 2.969,5.385 4.094,5.792 1.125,0.406 10 false Shift Lock Control Unit Assembly*3 5.271,4 6.813,4.406 1.542,0.406 10 false Certification ECU (Smart Key ECU Assembly)*1 5.271,3.844 5.729,4.042 0.458,0.198 10 false M67 5.604,3.5 6.365,3.698 0.76,0.198 10 false STP1 3.938,3.417 4.396,3.615 0.458,0.198 10 false 42 5.344,3.417 5.802,3.615 0.458,0.198 10 false 25 5.927,2.448 6.385,2.646 0.458,0.198 10 false A38 5.917,2.604 6.375,2.802 0.458,0.198 10 false ECM 4.021,4.76 4.271,4.958 0.25,0.198 10 false 8 4.375,4.76 4.625,4.958 0.25,0.198 10 false 4 5.281,1.646 5.74,1.844 0.458,0.198 10 false 10 5.365,0.854 5.583,1.042 0.219,0.188 10 false 9 4.198,0.844 4.417,1.031 0.219,0.188 10 false 3 4.198,1.646 4.417,1.833 0.219,0.188 10 false 5 3.979,1.74 4.188,1.938 0.208,0.198 10 false L 3.99,0.958 4.198,1.156 0.208,0.198 10 false L 5.531,0.854 5.927,1.052 0.396,0.198 10 false STP 5.531,1.635 5.927,1.833 0.396,0.198 10 false ST1- 0.219,5.563 2.573,5.854 2.354,0.292 10 false *1: w/ Entry and Start System 0.219,5.979 2.573,6.271 2.354,0.292 10 false *2: w/o Entry and Start System 2.875,4.021 4.406,4.448 1.531,0.427 10 false Skid Control ECU (Brake Actuator Assembly) 2.885,3.875 3.646,4.073 0.76,0.198 10 false A42 0.219,6.396 1.906,6.594 1.688,0.198 10 false *3: for CVT

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the ECM refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
C401044C60
1.469,0.135 1.969,0.385 0.5,0.25 0.917,1.75 1.417,1.25 true 1.917,1.75 2,1.25 true 2.417,1.75 2.167,1.25 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 0.75,1.802 1.094,1.979 0.344,0.177 10 false GND 1.865,1.802 2.104,1.979 0.24,0.177 10 false B 2.448,1.802 2.688,1.979 0.24,0.177 10 false B 1.594,0.167 1.938,0.344 0.344,0.177 10 false A91
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A91-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A91-7 (B) - Body ground Always 11 to 14 V
A91-6 (B) - Body ground Ignition switch to ON 11 to 14 V
A91-6 (B) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A38 ECM connector.


b.

Disconnect the A91 stop light switch assembly connector.


c.

Disconnect the A42 brake actuator assembly connector.


d.

Disconnect the M67 certification ECU connector.*

*: w/ Entry and Start System



e.

Disconnect the F18*1 or F19*2 Shift Lock Control Unit Assembly (for CVT) connector.

*1: w/o Entry and Start System

*2: w/ Entry and Start System



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-10 (ST1-) - A91-5 (L) Always Below 1 Ω
A38-9 (STP) - A91-3 (L) Always Below 1 Ω
A38-10 (ST1-) or A91-5 (L) - Body ground Always 10 kΩ or higher
A38-9 (STP) or A91-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR