Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for LHD) › 2019.09–2020.08
RM32H0E _54 Brake _060040 BRAKE SYSTEM (OTHER) _0298579 BRAKE BOOSTER(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the brake booster assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not performed Link

*1: When performing learning using the GTS

Click here(Click here)

Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

PROCEDURE

Hide 87211 1.REMOVE NO. 1 AIR DUCT

Hide 47201 2.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

Hide 47101A 3.REMOVE BRAKE PEDAL RETURN SPRING

Hide 4.LOOSEN CLEVIS LOCK NUT

a.
C142634C01
1.948,1.146 1.75,1.667 1.75,1.667 1.5,1.667 false 2.365,1.135 2.781,1.135 true 1.323,1.604 1.635,1.76 0.313,0.156 10 *1 2.833,1.073 3.146,1.229 0.313,0.156 10 *2
*1 Clevis Lock Nut
*2 Brake Master Cylinder Push Rod Clevis


Loosen the clevis lock nut of the brake master cylinder push rod clevis.


Hide 47264A 5.REMOVE PUSH ROD PIN

Hide 51441 6.REMOVE NO. 1 ENGINE UNDER COVER (for 8NR-FTS)

Hide 55225 7.REMOVE DASH PANEL HEAT INSULATOR (for 8NR-FTS)

a.
C366902

Remove the nut.


b.
C366880

Remove the 2 nuts and the dash panel heat insulator.


Hide 8.DISCONNECT CHECK VALVE TO CONNECTOR TUBE HOSE

a.
C273659

Slide the clip and disconnect the check valve to connector tube hose from the brake booster assembly.


Hide 44610 9.REMOVE BRAKE BOOSTER ASSEMBLY

a.

w/ Vacuum Warning Switch:

i.
C366908

Disconnect the vacuum warning switch connector.



b.
C366913

Disengage the 5 camps to remove the No. 1 brake tube clamp from the brake tubes.


c.

Disengage the 5 clamps to separate the No. 2 brake tube clamps from the brake tubes.


d.

Disengage the clamp to remove the No. 2 brake tube clamp from the vehicle body.


e.
C366906

Disengage the 2 clamps to separate the fuel pipe from the fuel pipe clamp.


f.
C366904C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the vehicle body.


g.
C366914

Remove the 4 nuts and push the brake booster assembly toward the engine compartment.

NOTICE:

Do not apply excessive force to the brake lines.



h.

Remove the brake master cylinder push rod clevis and lock nut from the brake booster assembly.


i.

Remove the brake booster assembly from the vehicle body.

NOTICE:

Do not apply excessive force to the brake lines or refrigerant lines.



Hide 44785 10.REMOVE BRAKE BOOSTER GASKET

a.

Remove the brake booster gasket from the brake booster assembly.