The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.
*1: When performing learning using the GTS
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>CALIBRATION
| *a | Heavy object exceeding the capacity of the engine lifter |
Because the weight of the engine with transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.
If work is not performed according to the procedures described in the repair manual, there is a danger that the engine lifter could drop and components could fall down.
| *a | High temperature areas |
Do not touch the engine or exhaust manifold converter sub-assembly when they are hot.
Touching the engine or exhaust manifold converter sub-assembly when they are hot could result in burns.
Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
for HFC-134a (R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf (R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFO-1234yf(R1234yf))>REPLACEMENT
3. DISCHARGE FUEL SYSTEM PRESSURE
4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
5.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>REMOVAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
6.REMOVE FRONT WHEELS
51441
7.REMOVE NO. 1 ENGINE UNDER COVER
Remove the 4 bolts, 4 screws, 4 clips and No. 1 engine under cover from the vehicle.
51444A
8.REMOVE REAR ENGINE UNDER COVER LH
Remove the 6 clips and rear engine under cover LH from the vehicle.
51443C
9.REMOVE REAR ENGINE UNDER COVER RH
Remove the 6 clips and rear engine under cover RH from the vehicle.
10.DRAIN ENGINE OIL
11.DRAIN ENGINE COOLANT
12.DRAIN COOLANT (for Intercooler)
13.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)
for 2WD:
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>OIL PAN>REMOVAL
for AWD:
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>OIL PAN>REMOVAL
14.DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle)
15.DRAIN TRANSFER OIL (for AWD)
16.REMOVE WINDSHIELD WIPER MOTOR AND LINK
55737B
17.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL
55735A
18.REMOVE WATER GUARD PLATE LH (for TMC Made RHD)
55736D
19.REMOVE COWL BODY MOUNTING REINFORCEMENT LH
55735C
20.REMOVE COWL BODY MOUNTING REINFORCEMENT RH
55701J
21.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
55701J
22.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
28800
23.REMOVE BATTERY
53141F
24.REMOVE RADIATOR COVER
17751
25.REMOVE NO. 1 AIR CLEANER INLET
17705
26.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE
| *1 | Air Cleaner Cap Sub-assembly Clamp |
| *2 | Guide |
Disconnect the mass air flow meter connector.
Disengage the clamp from the air cleaner cap sub-assembly.
Disengage the 2 air cleaner cap sub-assembly clamps.
Disengage the 2 guides to separate the air cleaner cap sub-assembly from the air cleaner case sub-assembly.
Loosen the hose clamp and remove the air cleaner cap with air cleaner hose from the No. 1 inlet air duct sub-assembly.
17701
27.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.
Remove the 2 bolts and air cleaner case sub-assembly from the vehicle.
89661
28.REMOVE ECM
29.DISCONNECT WIRE HARNESS
Remove the 2 bolts to separate the engine wire from the vehicle.
Remove the bolt and nut to separate the engine wire from the battery clamp sub-assembly.
Remove the 3 nuts to separate the engine wire from the positive (+) battery terminal.
| *A | for CVT |
| *B | for Manual Transaxle |
Remove the bolt to separate the engine wire from the transaxle assembly.
74404A
30.REMOVE BATTERY CLAMP SUB-ASSEMBLY
Disengage the clamp to separate the engine wire from the battery clamp sub-assembly.
Remove the 3 bolts and battery clamp sub-assembly from the vehicle.
16571C
31.DISCONNECT NO. 1 RADIATOR HOSE
Slide the clip and disconnect the No. 1 radiator hose from the water outlet.
16572D
32.DISCONNECT NO. 2 RADIATOR HOSE
Slide the clip and disconnect the No. 2 radiator hose from the water inlet with thermostat sub-assembly.
16551C
33.DISCONNECT NO. 1 INTERCOOLER COOLING WATER HOSE
16554C
34.DISCONNECT NO. 4 INTERCOOLER COOLING WATER HOSE
33820B
35.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for CVT)
for 2WD:
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>PARK / NEUTRAL POSITION SWITCH>REMOVAL
for AWD:
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>PARK / NEUTRAL POSITION SWITCH>REMOVAL
33820B
36.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)
44750
37.DISCONNECT UNION TO CONNECTOR TUBE HOSE
23829A
38.DISCONNECT FUEL VAPOR FEED HOSE
Slide the clip and disconnect the fuel vapor feed hose from the fuel vapor feed pipe.
87246
39.DISCONNECT OUTLET HEATER WATER HOSE
87245
40.DISCONNECT INLET HEATER WATER HOSE
23901
41.DISCONNECT FUEL TUBE SUB-ASSEMBLY
88703
42.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY
88704
43.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
44.SECURE STEERING WHEEL ASSEMBLY
45259A
45.REMOVE COLUMN HOLE COVER SILENCER SHEET
45260
46.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45025D
47.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
58166
48.REMOVE FRONT FLOOR COVER LH (w/ Cover)
58165B
49.REMOVE FRONT FLOOR COVER RH (w/ Cover)
Use the same procedure as for the LH side.
57533B
50.REMOVE FRONT FLOOR CENTER BRACE (for 2WD)
57533B
51.REMOVE FRONT FLOOR CENTER BRACE (for AWD)
17410
52.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (for 2WD)
17420K
53.REMOVE NO. 2 CENTER EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (for AWD)
17410
54.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for AWD)
37100
55.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for AWD)
56.REMOVE FRONT DRIVE SHAFT ASSEMBLY
for TMC Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY (for TMC Made)>REMOVAL
for TMMT Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY (for TMMT Made)>REMOVAL
11361J
57.REMOVE FLYWHEEL HOUSING UNDER COVER (for CVT)
32101G
58.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT (for CVT)
31481A
59.DISCONNECT NO. 1 CLUTCH HOSE (for Manual Transaxle)
Using a 10 mm union nut wrench, disconnect the bleeder clutch release tube from the No. 1 clutch hose.
Remove the clip and disconnect the No. 1 clutch hose from the clutch flexible hose bracket.
51108A
60.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH
51107A
61.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
62.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Set the engine assembly with transaxle on an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle and front suspension crossmember sub-assembly level.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.
To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.
Remove the 2 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.
| *A | for CVT |
| *B | for Manual Transaxle |
Remove the bolt and nut and separate the engine mounting insulator LH from the engine mounting bracket LH.
While holding the nut in place, loosen the bolt.
Remove the 6 bolts to separate the front suspension crossmember sub-assembly from the vehicle.
Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.
63.REMOVE WIRE HARNESS CLAMP BRACKET
Disengage the 3 clamps.
Remove the nut to separate the engine wire from the wire harness clamp bracket.
Remove the bolt and wire harness clamp bracket from the cylinder head sub-assembly.
64.INSTALL ENGINE HANGERS
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
|
Bolt |
Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-47060 |
| No. 2 Engine Hanger | 12282-47030 |
| Bolt | 91552-81030 |
Using an engine sling device and engine lift, secure the engine assembly with transaxle.
Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
12372A
65.REMOVE ENGINE MOUNTING INSULATOR LH
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
| *A | for CVT |
| *B | for Manual Transaxle |
Remove the 4 bolts, nut and engine mounting insulator LH from the vehicle.
12305
66.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
Remove the 2 bolts and No. 2 earth wire from the engine mounting insulator sub-assembly RH and vehicle.
Remove the bolt, nut and disconnect the air conditioner tube and accessory.
Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH from the vehicle.
67.REMOVE WATER HOSE (for CVT)
Disengage the 3 clamps from the engine assembly with transaxle.
Slide the 5 clips and remove the water hose from the engine assembly with transaxle.
68.REMOVE WATER HOSE (for Manual Transaxle)
Disengage the 3 clamps from the engine assembly with transaxle.
Slide the 3 clips and remove the water hose from the engine assembly with transaxle.
28100
69.REMOVE STARTER ASSEMBLY
for Denso Made without Stop and Start System:
for Valeo Made Cold Area Specification Vehicles:
for Valeo Made except Cold Area Specification Vehicles:
11363A
70.REMOVE FLYWHEEL HOUSING SIDE COVER
Remove the flywheel housing side cover from the cylinder block sub-assembly.
82121
71.REMOVE ENGINE WIRE
Disconnect all the clamps and connectors and remove the engine wire from the engine assembly with transaxle.
72.REMOVE ENGINE ASSEMBLY (for CVT)
73.REMOVE ENGINE ASSEMBLY (for Manual Transaxle)
32101B
74.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)
31250
75.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)
13405
76.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)
16361A
77.REMOVE FAN AND GENERATOR V BELT
16620
78.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Remove the 2 bolts and V-ribbed belt tensioner assembly from the timing chain cover assembly.
27020
79.REMOVE GENERATOR ASSEMBLY
for DENSO Made:
Click herePower Source / Network>8NR-FTS (BATTERY / CHARGING)>GENERATOR (for DENSO Made)>REMOVAL
for VALEO Made:
Click herePower Source / Network>8NR-FTS (BATTERY / CHARGING)>GENERATOR (for VALEO Made)>REMOVAL
88310
80.REMOVE COMPRESSOR WITH PULLEY ASSEMBLY
81.INSTALL ENGINE ASSEMBLY TO ENGINE STAND
Install the engine assembly to an engine stand.
82.REMOVE ENGINE HANGERS
Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger.