Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HIGH BEAM SYSTEM › 2019.09–2020.08
RM32H0E _59 Vehicle Exterior _060313 LIGHTING (EXT) _0303031 AUTOMATIC HIGH BEAM SYSTEM J

LIGHTING (EXT)  AUTOMATIC HIGH BEAM SYSTEM  Automatic High Beam System does not Operate or Operation Indicator does not Illuminate  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the automatic high beam system based on signals received from the forward recognition camera.

WIRING DIAGRAM

E367859E29
1.083,5.354 3,5.583 1.917,0.229 10 false : CAN Communication Line 0.385,4.104 2.302,4.333 1.917,0.229 10 false Forward Recognition Camera 0.375,2.74 2.292,2.969 1.917,0.229 10 false Combination Meter Assembly 2.333,1.677 4.25,1.906 1.917,0.229 10 false Auto High Beam Switch 2.344,1.531 2.781,1.802 0.438,0.271 10 false F6 1.99,1.021 2.427,1.292 0.438,0.271 10 false 3 4.063,1.021 4.5,1.292 0.438,0.271 10 false 6 5.167,0.99 5.604,1.26 0.438,0.271 10 false 17 5.438,1 5.875,1.271 0.438,0.271 10 false AHBI 5.979,0.708 6.302,0.938 0.323,0.229 10 false +B 5.135,4.115 5.573,4.385 0.438,0.271 10 false F15 5.135,4.26 6.771,4.729 1.635,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 2.177,1 2.615,1.271 0.438,0.271 10 false E 3.771,0.99 4.094,1.219 0.323,0.229 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

*1: w/ Entry and Start System




PROCEDURE

1.CHECK AUTOMATIC HIGH BEAM INDICATOR LIGHT
a.

Check the operation of the automatic high beam indicator light.

i.

Turn the ignition switch to ON.


ii.

Turn the light control switch to the AUTO or head position.


iii.

Turn the headlight dimmer switch to the high position.


iv.

Turn the automatic high beam main switch on.



OK:

Automatic high beam indicator light illuminate.


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

4.READ VALUE USING GTS
2.READ VALUE USING GTS
E367861C01
0.427,0.74 0.625,0.74 0.625,0.74 0.927,0.906 true 2.167,1.281 2.5,1.833 2.5,1.833 2.74,1.833 true 0.25,0.667 0.563,0.865 0.313,0.198 10 false *2 2.792,1.74 3.104,1.938 0.313,0.198 10 false *1 1.49,1.198 1.802,1.396 0.313,0.198 10 false *a
*1 Forward Recognition Camera
(Automatic High Beam Sensor)
*2 Work Light or Equivalent
*a 100 mm or less


a.

Shine a light on the automatic high beam sensor.

HINT:

If troubleshooting is being performed in a bright area, such as outside on a sunny day, it will not be necessary to perform this step.



b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Main Body / Data List.

Body Electrical > Main Body > Data List
Tester Display
Auto H Beam STS0
50003 123 169

f.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto H Beam STS0 Automatic high beam sensor current state Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err Condition can be displayed Undetec: Undetected
CAM NA: Camera detection malfunction*1
No sens: No detection
Hlight: Oncoming vehicles with headlights on
Taillgt: Preceding vehicles with taillights on
Speed: Vehicle speed
Daytime: Daytime state
Village: Urban area
Malfunc: System delay

*1: If CAM NA is displayed, the forward recognition camera may have stopped operating due to high temperature.


OK:

"Daytime" is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS

NG

REPLACE FORWARD RECOGNITION CAMERA

3.READ VALUE USING GTS
E367862C01
1.667,1.229 1.917,1.771 1.917,1.771 2.094,1.771 true 1,0.854 1.313,1.052 0.313,0.198 10 false *a 0.969,1.51 1.281,1.708 0.313,0.198 10 false *a 2.365,0.875 2.677,1.073 0.313,0.198 10 false *b 2.146,1.688 2.458,1.885 0.313,0.198 10 false *1
*1 Cardboard or Equivalent Object
*a 150 mm or more
*b 3 mm or more


a.

Cover the automatic high beam sensor with an opaque object, such as cardboard.

NOTICE:
·

Make sure that there is no clearance between the cardboard or equivalent object and the area of the windshield glass in front of the automatic high beam sensor.

·

If there is any clearance, light may shine on the automatic high beam sensor and the value of the Data List will not change.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Main Body / Data List.

Body Electrical > Main Body > Data List
Tester Display
Auto H Beam STS0
50003 123 169

f.

Read the Data List according to the display on the GTS.

HINT:

As it may take time for the values in the Data List to change, wait at least 10 seconds before reading the Data List.


Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto H Beam STS0 Automatic high beam sensor current state Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err Condition can be displayed Undetec: Undetected
CAM NA: Camera detection malfunction*1
No sens: No detection
Hlight: Oncoming vehicles with headlights on
Taillgt: Preceding vehicles with taillights on
Speed: Vehicle speed
Daytime: Daytime state
Village: Urban area
Malfunc: System delay

*1: If CAM NA is displayed, the forward recognition camera may have stopped operating due to high temperature.


OK:

"Speed" is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

NG

REPLACE FORWARD RECOGNITION CAMERA

4.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.

Body Electrical > Main Body > Data List
Tester Display
Auto High Beam Main Switch
50003 123 274

e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto High Beam Main Switch Auto high beam switch signal OFF or ON ON: Auto high beam switch pressed
OFF: Auto high beam switch not pressed
-
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS

NG

7.INSPECT AUTO HIGH BEAM SWITCH
5.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display
Auto H Beam STS0
50003 123 169
Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto H Beam STS0 Automatic high beam sensor current state Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err Condition can be displayed Undetec: Undetected
CAM NA: Camera detection malfunction*1
No sens: No detection
Hlight: Oncoming vehicles with headlights on
Taillgt: Preceding vehicles with taillights on
Speed: Vehicle speed
Daytime: Daytime state
Village: Urban area
Malfunc: System delay

*1: If CAM NA is displayed, the forward recognition camera may have stopped operating due to high temperature.


OK:

"Daytime" or "Speed" is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

6.PERFORM ACTIVE TEST USING GTS

NG

REPLACE FORWARD RECOGNITION CAMERA

6.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.

Body Electrical > Combination Meter > Active Test
Tester Display
Automatic High Beam Indicator
50004 122 104

e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Automatic High Beam Indicator Automatic high beam indicator light OFF or ON -
OK:

Automatic high beam indicator light illuminate.



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE COMBINATION METER ASSEMBLY

7.INSPECT AUTO HIGH BEAM SWITCH
a.

b.

Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (AUTO HIGH BEAM SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)

NG

8.CHECK HARNESS AND CONNECTOR (AUTO HIGH BEAM SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the F15 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-6 (+B) - F15-17 (AHBI) Always Below 1 Ω
F6-6 (+B) or F15-17 (AHBI) - Body ground Always 10 kΩ or higher
F6-3 (E) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR