The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the main body ECU (multiplex network body ECU) removal/installation are shown below.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 8NR-FTS:
for 3ZR-FAE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
73900
3.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)
67914
4.REMOVE FRONT DOOR SCUFF PLATE LH (w/o Driver Side Knee Airbag)
62112
5.REMOVE COWL SIDE TRIM BOARD LH (w/o Driver Side Knee Airbag)
55606
6.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/o Driver Side Knee Airbag)
55470
7.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY (w/o Driver Side Knee Airbag)
55434B
8.REMOVE INSTRUMENT PANEL LOWER CENTER FINISH PANEL (w/o Driver Side Knee Airbag)
55404D
9.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)
53601
10.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (w/o Driver Side Knee Airbag)
55545
11.REMOVE FUSE BOX OPENING COVER (w/o Driver Side Knee Airbag)
55308B
12.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY
82730
13.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU
Disengage the clamp.
Disconnect 4 connectors.
|
Remove in this Direction |
Disengage the claws and pull down the lock levers to disconnect the 2 connectors as shown in the illustration.
Remove the bolt and nut.
Disengage the clamp.
Pull out the instrument panel junction block assembly with main body ECU.
Disengage the clamp.
|
Remove in this Direction |
Disengage the clamp.
Disengage the claws and pull down the lock levers to disconnect the 2 connectors as shown in the illustration.
Remove the instrument panel junction block assembly with main body ECU.
89221
14.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Remove the bolt.
Disengage the clamp to remove the wiring harness clamp bracket.
| *1 | Instrument Panel Junction Block Assembly |
| *2 | Main Body ECU (Multiplex Network Body ECU) |
|
Push in this Direction |
Press the claw of the instrument panel junction block assembly as shown in the illustration to release the lock.
| *a | Protective Tape |
|
Insert in this Direction |
|
Remove in this Direction |
With the instrument panel junction block assembly lock released, insert a screwdriver with its tip wrapped in protective tape horizontally between the main body ECU (multiplex network body ECU) and the instrument panel junction block assembly.
Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).
Do not insert the screwdriver under the connector socket of the main body ECU (multiplex network body ECU).
Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) to the position where the connector becomes disconnected.
Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Raise the main body ECU (multiplex network body ECU) as shown by the arrow (1), and then pull it out as shown by the arrow (2) in the illustration.
Do not touch the main body ECU (multiplex network body ECU) connector.