Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2019.09
RM32H0E _58 Vehicle Interior _060061 SUPPLEMENTAL RESTRAINT SYSTEMS _0294190 AIRBAG SYSTEM D

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  DIAGNOSIS SYSTEM  



FUNCTION OF SRS WARNING LIGHT


a.

Primary check

i.

Turn the ignition switch off. Wait for at least 2 seconds, then turn the ignition switch to ON. The SRS warning light comes on for approximately 6 seconds and diagnosis of the airbag system is performed.

HINT:

If malfunctions are detected during the primary check, the SRS warning light remains on even after the primary check period of approximately 6 seconds.




b.

Constant check

i.

After the primary check, the airbag sensor assembly constantly monitors the airbag system for malfunctions.

HINT:
If malfunctions are detected during the constant check, the airbag sensor assembly will indicate the malfunction as follows:
·

The SRS warning light comes on.

·

The SRS warning light goes off, and then comes on. This indicates a source voltage drop. The SRS warning light goes off 10 seconds after the source voltage returns to normal.





c.

Review

i.

When the airbag system is normal:

The SRS warning light comes on only during the primary check period of approximately 6 seconds after the ignition switch is turned to ON.


ii.

When the airbag system is malfunctioning:

·

The SRS warning light remains on even after the primary check period.

·

The SRS warning light goes off after the primary check, but comes on again during the constant check.

·

The SRS warning light does not come on when the ignition switch is turned from off to ON.


HINT:

The SRS warning light will remain illuminated if any airbag or pretensioner has been deployed.





SRS WARNING LIGHT CHECK


a.
C265591

Turn the ignition switch to ON, and check that the SRS warning light comes on for approximately 6 seconds (primary check).


b.

Check that the SRS warning light goes off approximately 6 seconds after the ignition switch is turned to ON (constant check).

HINT:

When any of the following symptoms occur, refer to Problem Symptoms Table.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PROBLEM SYMPTOMS TABLE

·

The SRS warning light comes on occasionally after the primary check period.

·

The SRS warning light comes on, but DTCs are not output.

·

The ignition switch is turned from off to ON, but the SRS warning light does not come on.





FUNCTION OF PASSENGER AIRBAG ON/OFF INDICATOR (w/ Airbag Cut Off Switch)


a.

Initial check

i.

Turn the ignition switch to ON.


ii.

The passenger airbag ON/OFF indicator comes on for approximately 4 seconds, then turns off for approximately 2 seconds.

C355684E07
4.865,3.385 6.99,4.417 2.125,1.031 10 false ON/OFF condition depends on the airbag cut off switch cylinder sub-assembly status result.*1 0.333,0.438 1.51,0.833 1.177,0.396 10 false Ignition Switch 1.885,0.646 2.427,1.052 0.542,0.406 10 false OFF 1.885,0.26 2.479,0.552 0.594,0.292 10 false ON 1.885,1.854 2.427,2.26 0.542,0.406 10 false OFF 1.885,2.99 2.427,3.396 0.542,0.406 10 false OFF 1.885,1.469 2.375,1.729 0.49,0.26 10 false ON 1.885,2.604 2.333,2.875 0.448,0.271 10 false ON 3.417,1.167 3.906,2.167 0.49,1 10 false 4 sec. 3.417,2.292 3.979,2.594 0.563,0.302 10 false 4 sec. 4.417,1.156 4.917,1.417 0.5,0.26 10 false 2 sec. 4.427,2.302 4.896,2.563 0.469,0.26 10 false 2 sec. 0.333,1.5 1.458,2.583 1.125,1.083 10 false Passenger Airbag ON/OFF Indicator ("ON") 0.333,2.604 1.458,3.781 1.125,1.177 10 false Passenger Airbag ON/OFF Indicator ("OFF") 0.167,4.281 6.083,4.615 5.917,0.333 10 false *1: The ON indicator illuminates for approximately 60 seconds and then turns off.


iii.

Approximately 6 seconds after the ignition switch is turned to ON, the passenger airbag ON/OFF indicator will indicate ON/OFF according to the airbag cut off switch cylinder sub-assembly condition as listed below.

Indicator Operation
Airbag Cut Off Switch Cylinder Sub-assembly Condition Passenger Airbag ON/OFF Indicator SRS Warning Light
ON Indicator OFF Indicator

*1: The ON indicator illuminates for approximately 60 seconds and then turns off.

ON ON*1 OFF OFF
OFF OFF ON OFF
Switch failure OFF ON ON

HINT:

If the SRS warning light is not illuminated and the passenger airbag ON/OFF indicator does not operate as specified in the table according to the airbag cut off switch cylinder sub-assembly status, no related DTCs will be stored. Proceed to the Trouble in Passenger Airbag ON/OFF Indicator troubleshooting procedure.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>Trouble in Passenger Airbag ON/OFF Indicator





PASSENGER AIRBAG ON/OFF INDICATOR CHECK (w/ Airbag Cut Off Switch)


a.

Turn the ignition switch to ON.


b.

Check that the passenger airbag ON/OFF indicator ("ON" and "OFF") comes on for approximately 4 seconds, then goes off for approximately 2 seconds.

HINT:

Refer to the indicator operation table in Function of Passenger Airbag ON/OFF Indicator for the passenger airbag ON/OFF indicator operation when the ignition switch is turned to ON and approximately 6 seconds elapse.




FUNCTION OF SRS CONNECTORS


a.

Location of activation prevention mechanism

C422527E01
4.917,0.208 7,0.542 2.083,0.333 10 false Airbag Sensor Assembly 0.167,0.906 3.354,1.229 3.188,0.323 10 false Rear Seat 3 Point Type Outer Belt Assembly LH*1 0.583,1.417 3.25,1.75 2.667,0.333 10 false Front Seat Outer Belt Assembly LH 0.583,1.948 3.083,2.25 2.5,0.302 10 false Curtain Shield Airbag Assembly LH*2 0.583,2.448 2.833,2.802 2.25,0.354 10 false Front Seat Airbag Assembly LH*2 0.167,2.979 3.344,3.313 3.177,0.333 10 false Lower No. 1 Instrument Panel Airbag Assembly*3 0.167,3.5 4.083,3.833 3.917,0.333 10 false Instrument Panel Passenger without Door Airbag Assembly 0.333,4.021 1.948,4.354 1.615,0.333 10 false Horn Button Assembly 2.667,4.021 5.125,4.354 2.458,0.333 10 false Spiral Cable with Sensor Sub-assembly 0.583,6.188 3.167,6.521 2.583,0.333 10 false Front Seat Airbag Assembly RH*2 0.583,5.667 3.25,5.979 2.667,0.313 10 false Curtain Shield Airbag Assembly RH*2 0.583,5.146 3.25,5.469 2.667,0.323 10 false Front Seat Outer Belt Assembly RH 0.167,4.615 3.344,4.927 3.177,0.313 10 false Rear Seat 3 Point Type Outer Belt Assembly RH*1 0.521,6.688 3.594,7 3.073,0.313 10 false : Activation Prevention Mechanism Connector 0.167,7 3.25,7.333 3.083,0.333 10 false *1: w/ Rear Pretensioner 0.167,7.333 3.25,7.667 3.083,0.333 10 false *2: w/ Side Airbag 0.167,7.667 3.25,8 3.083,0.333 10 false *3: w/ Driver Side Knee Airbag


b.

Function of activation prevention mechanism

C238382E20
1.583,1.063 1.198,0.917 false 5.26,1.521 5.26,2.042 true 1.844,1.667 1.844,2.083 true 1.656,1.448 1.198,1.448 true 2.646,1.646 2.969,1.646 true 2.354,1.385 3,0.969 3,0.969 2.552,1.458 true 1.771,0.375 2.51,0.708 0.74,0.333 10 false When open 0.313,0.833 1.208,1.146 0.896,0.313 10 false Male Housing 3.042,0.885 4.115,1.229 1.073,0.344 10 false Female Terminal 0.302,1.375 1.198,1.698 0.896,0.323 10 false Male Terminal 3.01,1.573 4.073,1.938 1.063,0.365 10 false Female Housing 1.26,2.104 2.448,2.448 1.188,0.344 10 false Short Spring Plate 5.448,0.375 6.354,0.75 0.906,0.375 10 false When shorted 4.375,2.063 6.156,2.635 1.781,0.573 10 false Short spring plate contacting the male terminal

i.

This mechanism is designed to create a short circuit automatically between the positive (+) and negative (-) terminals of an airbag power source connector when disconnected.


ii.

The short spring plate contained in the connector creates a closed circuit on the squib side (no potential difference can occur between both terminals), preventing accidental squib deployment when servicing.



c.

Releasing of activation prevention mechanism

i.

To release the activation prevention mechanism, insert a piece of paper with the same thickness as the male terminal (approximately 0.5 mm (0.0197 in.)) between the terminals and short spring to break the connection.


ii.

Refer to the following illustrations concerning connectors utilizing the activation prevention mechanism and its release method.

CAUTION:

Never release the activation prevention mechanism on the squib connector even when inspecting with the squib disconnected.


NOTICE:
·

Do not release the activation prevention mechanism unless specified by the troubleshooting procedure.

·

To prevent the terminals and short spring from being damaged, always use a piece of paper with the same thickness as the male terminal.



C422528E01
1.667,0.5 2.083,0.729 0.417,0.229 3.333,0.5 3.75,0.729 0.417,0.229 5,0.5 5.417,0.729 0.417,0.229 0.115,5.99 0.479,6.219 0.365,0.229 1.26,7.5 1.625,7.729 0.365,0.229 2.313,3.615 1.802,4.24 1.802,4.24 2.323,3.208 true 1.823,4.208 2.302,3.417 true 5.438,3.625 4.927,4.25 4.927,4.25 5.448,3.219 true 4.969,4.198 5.448,3.406 true 2.875,3.156 3.313,2.771 3.313,2.771 2.979,3.563 true 2.906,3.365 3.302,2.792 true 5.844,3.156 6.281,2.771 6.281,2.771 5.948,3.563 true 5.875,3.365 6.271,2.792 true 3.813,5.635 4.115,5.229 true 3.104,6.354 3.104,5.594 true 6.063,5.635 6.365,5.229 true 2.24,8.094 2.75,7.677 true 3.5,7.625 4.01,7.208 true 4.979,8.094 5.49,7.677 true 6,7.635 6.51,7.219 true 5.323,6.354 5.323,5.594 true 0.115,0.063 4.323,0.406 4.208,0.344 12 false Wire Harness Connector (to Airbag Sensor Assembly): 1.708,0.531 2.375,0.917 0.667,0.385 10 false M103 3.385,0.531 4.052,0.917 0.667,0.385 10 false F150 5.042,0.531 5.708,0.917 0.667,0.385 10 false M102 1.438,2.365 2.729,2.771 1.292,0.406 10 false Before Release 4.594,2.365 5.885,2.771 1.292,0.406 10 false After Release 1.448,4.24 2.74,4.646 1.292,0.406 10 false Short Spring 4.552,4.25 5.844,4.656 1.292,0.406 10 false Short Spring 3.344,2.688 3.865,2.99 0.521,0.302 10 false Paper 6.313,2.688 6.833,2.99 0.521,0.302 10 false Paper 0.125,4.667 4,5 3.875,0.333 12 false Spiral Cable with Sensor Sub-assembly Connector: 0.188,6.021 0.906,6.344 0.719,0.323 10 false F30 2.906,5 4,5.333 1.094,0.333 10 false Before Release 5.156,5 6.167,5.333 1.01,0.333 10 false After Release 4.052,7.115 4.573,7.417 0.521,0.302 10 false Paper 2.75,6.375 3.833,6.667 1.083,0.292 10 false Short Spring 4.958,6.365 6,6.667 1.042,0.302 10 false Short Spring 6.406,5.104 6.917,5.417 0.51,0.313 10 false Paper 0.125,6.635 3.083,6.969 2.958,0.333 12 false No. 2 Instrument Panel Wire Connector: 1.313,7.531 1.635,7.74 0.323,0.208 10 false Fb1 0.521,8.385 1.802,8.698 1.281,0.313 10 false : Short Spring 2.583,6.958 3.719,7.24 1.135,0.281 10 false Before Release 5.167,6.938 6.5,7.25 1.333,0.313 10 false After Release 1.875,8.104 2.917,8.427 1.042,0.323 10 false Short Spring 4.625,8.115 5.667,8.438 1.042,0.323 10 false Short Spring 6.563,7.115 7.083,7.417 0.521,0.302 10 false Paper 4.146,5.104 4.667,5.417 0.521,0.313 10 false Paper