This circuit detects the airbag cut off switch cylinder sub-assembly status.
The passenger airbag ON/OFF indicator comes on to inform the driver of the instrument panel passenger without door airbag assembly status (activated or deactivated).
Refer to the normal condition of the passenger airbag ON/OFF indicator.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Turn the ignition switch to ON, and check the SRS warning light condition.
After the primary check period, the SRS warning light turns off.
If the SRS warning light is on when this malfunction occurs, a DTC is stored. Troubleshoot for the stored DTC.
The primary check period is approximately 6 seconds after the ignition switch is turned to ON.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the connectors from the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Airbag Cut Off Switch Cylinder Sub-assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly) |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F64-2 (PMC+) - Body ground | Ignition switch ON | Below 1 V |
| F64-1 (PMC-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Using a service wire, connect terminals 22 (MSW+) and 21 (MSW-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-2 (PMC+) - F64-1 (PMC-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-2 (PMC+) - F64-1 (PMC-) | Always | 1 MΩ or higher |
| F64-2 (PMC+) - Body ground | Always | 1 MΩ or higher |
| F64-1 (PMC-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the airbag cut off switch cylinder sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG CUT-OFF SWITCH>REMOVAL
Inspect the airbag cut off switch cylinder sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG CUT-OFF SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG