Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2019.09
RM32H0E _58 Vehicle Interior _060061 SUPPLEMENTAL RESTRAINT SYSTEMS _0294190 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B162B  Side Airbag Sensor Assembly No.2 Lost Communication (RH)  B162C  Side Airbag Sensor Assembly No.2 Initialization Error (RH)  


DESCRIPTION

The side collision sensor RH circuit (bus 2) consists of the airbag sensor assembly and floor side airbag sensor RH.

The floor side airbag sensor RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 2).

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B162B Side Airbag Sensor Assembly No.2 Lost Communication (RH) Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 2).

·

The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 2).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 2).

·

The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 2).

·

Floor side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Floor side airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode
B162C Side Airbag Sensor Assembly No.2 Initialization Error (RH) Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 2).

·

The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 2).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 2).

·

The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 2).

·

Floor side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Floor side airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode

DTC Detection Conditions (B162B):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Ignition switch ON ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 2) ○ - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 2) - ○ - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 2) - - ○ - - -
The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 2) - - - ○ - -
Floor side airbag sensor RH malfunction - - - - ○ -
Airbag sensor assembly malfunction - - - - - ○
Detection Time - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B162C):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Ignition switch ON ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 2) ○ - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 2) - ○ - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 2) - - ○ - - -
The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 2) - - - ○ - -
Floor side airbag sensor RH malfunction - - - - ○ -
Airbag sensor assembly malfunction - - - - - ○
Detection Time - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

B473434E47
4.781,2.917 6.49,3.354 1.708,0.438 10 false Airbag Sensor Assembly 4.771,2.74 5.333,2.948 0.563,0.208 10 false M103 4.823,1.01 5.938,1.438 1.115,0.427 10 false BCR+ 5.49,1.458 6.604,1.885 1.115,0.427 10 false Interface 4.583,1.01 5.698,1.438 1.115,0.427 10 false 28 4.823,1.688 5.938,2.115 1.115,0.427 10 false BCR- 4.583,1.688 5.698,2.115 1.115,0.427 10 false 27 2.594,1.01 3.708,1.438 1.115,0.427 10 false BFR+ 2.604,1.698 3.719,2.125 1.115,0.427 10 false BFR- 3.052,1.01 4.167,1.438 1.115,0.427 10 false 2 3.052,1.698 4.167,2.125 1.115,0.427 10 false 1 1.771,1.458 2.885,1.885 1.115,0.427 10 false Interface 0.771,1.458 1.885,1.885 1.115,0.427 10 false Element 0.552,2.344 0.99,2.552 0.438,0.208 10 false M34 0.552,2.521 2.427,2.802 1.875,0.281 10 false Floor Side Airbag Sensor RH

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and floor side airbag sensor RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and floor side airbag sensor RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

2.CHECK FLOOR WIRE (OPEN)
a.
B474700C13
0.75,0.865 1.188,1.104 0.438,0.24 0.969,3.719 1.313,3.948 0.344,0.229 1.885,1.823 1.885,1.677 false 1.427,1.688 1.823,1.292 true 2.333,1.698 1.927,1.292 true 1.573,4.229 1.802,3.854 true 2.25,4.229 2,3.854 true 1.625,2.854 1.625,2.438 1.625,2.438 1.458,2.438 false 0.76,2.844 1.219,3.198 0.458,0.354 10 false *1 2.521,2.573 2.927,2.927 0.406,0.354 10 false *2 1.313,2.365 1.781,2.865 0.469,0.5 10 false *3 1.823,1.833 2.208,2.26 0.385,0.427 10 false *c 0.677,0.208 1.135,0.677 0.458,0.469 10 false *a 0.719,3.438 1.229,4.125 0.51,0.688 10 false *b 2.188,2.844 2.594,3.198 0.406,0.354 10 false A 1.885,2.844 2.292,3.198 0.406,0.354 10 false B 1.292,2.844 1.698,3.198 0.406,0.354 10 false C 0.979,2.844 1.385,3.198 0.406,0.354 10 false D 0.792,0.896 1.167,1.208 0.375,0.313 10 false M103 1.021,3.75 1.521,4.063 0.5,0.313 10 false M34 2.198,1.698 2.698,2.01 0.5,0.313 10 false BCR+ 1.271,1.698 1.771,2.01 0.5,0.313 10 false BCR- 2.135,4.24 2.635,4.552 0.5,0.313 10 false BFR+ 1.427,4.24 1.927,4.552 0.5,0.313 10 false BFR-
*1 Floor Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Floor Side Airbag Sensor RH)
*c Service Wire


Using a service wire, connect terminals 28 (BCR+) and 27 (BCR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M34-2 (BFR+) - M34-1 (BFR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (SHORT)
a.
C341628C05
0.583,2.25 1,2.5 0.417,0.25 1.646,0.979 1.646,0.313 1.646,0.313 1.396,0.313 false 1.052,2.813 1.438,2.375 true 2.104,2.823 1.719,2.385 true 0.698,0.958 1.135,1.354 0.438,0.396 10 false *1 2.583,0.698 2.958,1.135 0.375,0.438 10 false *2 1.24,0.24 1.74,0.813 0.5,0.573 10 false *3 0.427,1.854 0.833,2.281 0.406,0.427 10 false *a 1.979,2.833 2.563,3.25 0.583,0.417 10 false BFR+ 0.906,2.833 1.49,3.25 0.583,0.417 10 false BFR- 0.667,2.292 1.042,2.542 0.375,0.25 10 false M34 2.219,0.958 2.594,1.396 0.375,0.438 10 false A 1.906,0.958 2.281,1.396 0.375,0.438 10 false B 1.313,0.958 1.688,1.396 0.375,0.438 10 false C 1.01,0.958 1.385,1.396 0.375,0.438 10 false D
*1 Floor Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Floor Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M34-2 (BFR+) - M34-1 (BFR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT TO B+)
a.
C341628C05
0.583,2.25 1,2.5 0.417,0.25 1.646,0.979 1.646,0.313 1.646,0.313 1.396,0.313 false 1.052,2.813 1.438,2.375 true 2.104,2.823 1.719,2.385 true 0.698,0.958 1.135,1.354 0.438,0.396 10 false *1 2.583,0.698 2.958,1.135 0.375,0.438 10 false *2 1.24,0.24 1.74,0.813 0.5,0.573 10 false *3 0.427,1.854 0.833,2.281 0.406,0.427 10 false *a 1.979,2.833 2.563,3.25 0.583,0.417 10 false BFR+ 0.906,2.833 1.49,3.25 0.583,0.417 10 false BFR- 0.667,2.292 1.042,2.542 0.375,0.25 10 false M34 2.219,0.958 2.594,1.396 0.375,0.438 10 false A 1.906,0.958 2.281,1.396 0.375,0.438 10 false B 1.313,0.958 1.688,1.396 0.375,0.438 10 false C 1.01,0.958 1.385,1.396 0.375,0.438 10 false D
*1 Floor Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Floor Side Airbag Sensor RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch off.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M34-2 (BFR+) - Body ground Ignition switch ON Below 1 V
M34-1 (BFR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

5.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C341628C05
0.583,2.25 1,2.5 0.417,0.25 1.646,0.979 1.646,0.313 1.646,0.313 1.396,0.313 false 1.052,2.813 1.438,2.375 true 2.104,2.823 1.719,2.385 true 0.698,0.958 1.135,1.354 0.438,0.396 10 false *1 2.583,0.698 2.958,1.135 0.375,0.438 10 false *2 1.24,0.24 1.74,0.813 0.5,0.573 10 false *3 0.427,1.854 0.833,2.281 0.406,0.427 10 false *a 1.979,2.833 2.563,3.25 0.583,0.417 10 false BFR+ 0.906,2.833 1.49,3.25 0.583,0.417 10 false BFR- 0.667,2.292 1.042,2.542 0.375,0.25 10 false M34 2.219,0.958 2.594,1.396 0.375,0.438 10 false A 1.906,0.958 2.281,1.396 0.375,0.438 10 false B 1.313,0.958 1.688,1.396 0.375,0.438 10 false C 1.01,0.958 1.385,1.396 0.375,0.438 10 false D
*1 Floor Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Floor Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M34-2 (BFR+) - Body ground Always 1 MΩ or higher
M34-1 (BFR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK FLOOR SIDE AIRBAG SENSOR RH

NG

REPLACE FLOOR WIRE

6.CHECK FLOOR SIDE AIRBAG SENSOR RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Floor Side Airbag Sensor LH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the floor side airbag sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B162B, B162C, B163B and B163C may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B162B or B162C is output. A
DTC B163B or B163C is output. B
DTCs B162B, B162C, B163B and B163C are not output. C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the floor side airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C