The transponder key ECU assembly blinks the security indicator light when the immobiliser is set.
If the transponder key ECU assembly is replaced, refer to Service Bulletin.
Check the vehicle specification.
| Result | Proceed to |
|---|---|
| w/o Theft Deterrent System | A |
| w/ Theft Deterrent System | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Immobiliser / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Security Indicator | Security indicator light | ON/OFF | - |
| Tester Display |
|---|
| Security Indicator |
Security indicator light can be turned on and off using the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect F137 transponder key ECU assembly connector.
Disconnect the F81 security indicator light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F81-9 (LP) - F137-8 (IND) | Always | Below 1 Ω |
| F81-9 (LP) - Body ground | Always | 10 kΩ or higher |
| F137-8 (IND) - Body ground | Always | 10 kΩ or higher |
| F81-5 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F137 transponder key ECU assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F81-9 (LP) - Body ground | Key not in ignition key cylinder | Pulse generation |
| Key in ignition key cylinder | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Immobiliser or Main Body / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Security Indicator | Security indicator light | ON/OFF | - |
| Tester Display |
|---|
| Security Indicator |
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Security Indicator | Security indicator light | ON/OFF | - |
| Tester Display |
|---|
| Security Indicator |
| Result | Proceed to |
|---|---|
| Security indicator light operation is normal when performing the "Main Body" and "Immobiliser" Active Test | A |
·
Security indicator light operation is not normal when performing the "Immobiliser" Active Test ·
Security indicator light operation is normal when performing the "Main Body" Active Test |
B |
·
Security indicator light operation is normal when performing the "Immobiliser" Active Test ·
Security indicator light operation is not normal when performing the "Main Body" Active Test |
C |
| Security indicator light operation is not normal when performing the "Main Body" and "Immobiliser" Active Test | D |
A
B
C
D
When the immobiliser is set, check that the security indicator light blinks.*1
The security indicator light blinks normally.
When the theft deterrent system is in the arming preparation state, check that the security indicator light is on.*2
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION
The security indicator light is on.
| Result | Proceed to |
|---|---|
| Both *1 and *2 are OK | A |
| *1 is NG (*2 is OK) | B |
| *2 is NG (*1 is OK) (for LHD) | C |
| *2 is NG (*1 is OK) (for RHD) | D |
| Both *1 and *2 are NG | E |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
D
E
Disconnect the F81 security indicator light connector.
Disconnect the F137 transponder key ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F137-8 (IND) - F81-9 (LP) | Always | Below 1 Ω |
| F137-8 (IND) - Body ground | Always | 10 kΩ or higher |
| F81-9 (LP) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F81 security indicator light connector.
Disconnect the F15 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F15-15 (IND) - F81-9 (LP) | Always | Below 1 Ω |
| F15-15 (IND) - Body ground | Always | 10 kΩ or higher |
| F81-9 (LP) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Disconnect the F81 security indicator light connector.
Disconnect F137 transponder key ECU assembly connector.
Disconnect the F15 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F137-8 (IND) - F81-9 (LP) | Always | Below 1 Ω |
| F15-15 (IND) - F81-9 (LP) | Always | Below 1 Ω |
| F137-8 (IND) - Body ground | Always | 10 kΩ or higher |
| F15-15 (IND) - Body ground | Always | 10 kΩ or higher |
| F81-9 (LP) - Body ground | Always | 10 kΩ or higher |
| F81-5 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the security indicator light (clock assembly) with a new or known good one.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>CLOCK>REMOVAL
When the immobiliser is set or theft deterrent system is in the arming preparation state, check that the security indicator light blinks.
Security indicator light blinks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the transponder key ECU assembly with a new or known good one.
Refer to Service Bulletin.
When the immobiliser is set or theft deterrent system is in the arming preparation state, check that the security indicator light blinks.
Security indicator light blinks.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C