There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
| Symptom | Trouble Area |
|---|---|
| Resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU (network gateway ECU) is below 54 Ω. | ·
Short in CAN main bus lines ·
Short in CAN branch lines ·
Central gateway ECU (network gateway ECU) ·
Airbag sensor assembly ·
Steering sensor ·
Power steering ECU assembly ·
Brake actuator assembly ·
4WD ECU assembly (for AWD) ·
No. 5 CAN junction connector (for LHD) ·
No. 4 CAN junction connector (for LHD) ·
No. 4 CAN junction connector (for RHD) ·
No. 5 CAN junction connector (for RHD) |
for LHD
for RHD
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the cruise control main switch on, turn the LDA main switch on and then drive the vehicle at a speed of 60 km/h (37 mph) or more for approximately 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Check vehicle type.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 5 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | to No. 4 CAN Junction Connector |
| *c | to Central Gateway ECU (Network Gateway ECU) | *d | to Brake Actuator Assembly |
| *e | to 4WD ECU Assembly
(for AWD) |
- | - |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F124-1 (CANH) - F124-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 4 CAN junction connector |
| F124-2 (CANH) - F124-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Central gateway ECU (network gateway ECU) |
| F124-5 (CANH) - F124-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Brake actuator assembly |
| F124-6 (CANH) - F124-17 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | 4WD ECU Assembly*1 |
*1: for AWD
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to No. 4 CAN junction connector) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the F74 central gateway ECU (network gateway ECU) connector.
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
| *b | to Central Gateway ECU (Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F124-2 (CANH) - F124-13 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the F124 No. 5 CAN junction connector.
Disconnect the No. 4 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | to Airbag Sensor Assembly |
| *c | to Steering Sensor | *d | to Power Steering ECU Assembly |
| *e | to No. 5 CAN Junction Connector | - | - |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F123-1 (CANH) - F123-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Airbag sensor assembly |
| F123-5 (CANH) - F123-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Steering sensor |
| F123-6 (CANH) - F123-17 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Power steering ECU assembly |
| F123-7 (CANH) - F123-18 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 5 CAN junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 5 CAN junction connector) | B |
| NG (Line to Airbag sensor assembly) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the F150 airbag sensor assembly connector.
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
| *b | to Airbag Sensor Assembly |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F123-1 (CANH) - F123-12 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 5 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 8 CAN Junction Connector) |
*b | to No. 6 CAN Junction Connector |
| *c | to Central Gateway ECU (Network Gateway ECU) | *d | to Brake Actuator Assembly |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F117-1 (CANH) - F117-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 6 CAN junction connector |
| F117-2 (CANH) - F117-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Central gateway ECU (network gateway ECU) |
| F117-7 (CANH) - F117-18 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Brake actuator assembly |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to No. 4 CAN junction connector) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the F74 central gateway ECU (network gateway ECU) connector.
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
| *b | to Central Gateway ECU (Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F117-2 (CANH) - F117-13 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the F117 No. 5 CAN junction connector.
Disconnect the No. 4 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | to Airbag Sensor Assembly |
| *c | to Power Steering ECU Assembly | *d | to 4WD ECU Assembly
(for AWD) |
| *e | to Steering Sensor | *f | to No. 5 CAN Junction Connector |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F115-1 (CANH) - F115-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Airbag sensor assembly |
| F115-3 (CANH) - F115-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Power steering ECU assembly |
| F115-4 (CANH) - F115-15 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | 4WD ECU assembly*1 |
| F115-5 (CANH) - F115-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Steering sensor |
| F115-6 (CANH) - F115-17 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 5 CAN junction connector |
*1: for AWD
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 5 CAN junction connector) | B |
| NG (Line to Airbag sensor assembly) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the F150 airbag sensor assembly connector.
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
| *b | to Airbag Sensor Assembly |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F115-1 (CANH) - F115-12 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F74-22 (CA2H) - F74-7 (CA2L) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.
| Result |
|---|
| OK |
| NG |
OK
NG