Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › 2019.09–2021.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P020113  Cylinder 1 Injector "A" Circuit Open  P020213  Cylinder 2 Injector "A" Circuit Open  P020313  Cylinder 3 Injector "A" Circuit Open  P020413  Cylinder 4 Injector "A" Circuit Open  P062D13  Fuel Injector Driver Circuit Performance Bank 1 Circuit Open  


DESCRIPTION

The D-4 system is a direct injection fuel system which injects highly pressurized fuel directly into the combustion chamber. An injector driver (EDU), which is built into the ECM, is used to operate the fuel injector assemblies at high speed. The EDU receives injection request signals from the ECM and converts them to high voltage/high current injector operation signals to operate the fuel injector assemblies.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P020113 Cylinder 1 Injector "A" Circuit Open Either of following conditions is met (1 trip detection logic):
·

Short to +B in No. 1 fuel injector assembly circuit for 40 times or more.

·

Open or short to ground in No. 1 fuel injector assembly circuit for 20 times or more.


·

Open or short in fuel injector assembly circuit

·

Fuel injector assembly

·

D INJ relay

·

ECM


Comes on DTC stored SAE Code:
P0201
P020213 Cylinder 2 Injector "A" Circuit Open Either of following conditions is met (1 trip detection logic):
·

Short to +B in No. 2 fuel injector assembly circuit for 40 times or more.

·

Open or short to ground in No. 2 fuel injector assembly circuit for 20 times or more.


·

Open or short in fuel injector assembly circuit

·

Fuel injector assembly

·

D INJ relay

·

ECM


Comes on DTC stored SAE Code:
P0202
P020313 Cylinder 3 Injector "A" Circuit Open Either of following conditions is met (1 trip detection logic):
·

Short to +B in No. 3 fuel injector assembly circuit for 40 times or more.

·

Open or short to ground in No. 3 fuel injector assembly circuit for 20 times or more.


·

Open or short in fuel injector assembly circuit

·

Fuel injector assembly

·

D INJ relay

·

ECM


Comes on DTC stored SAE Code:
P0203
P020413 Cylinder 4 Injector "A" Circuit Open Either of following conditions is met (1 trip detection logic):
·

Short to +B in No. 4 fuel injector assembly circuit for 40 times or more.

·

Open or short to ground in No. 4 fuel injector assembly circuit for 20 times or more.


·

Open or short in fuel injector assembly circuit

·

Fuel injector assembly

·

D INJ relay

·

ECM


Comes on DTC stored SAE Code:
P0204
P062D13 Fuel Injector Driver Circuit Performance Bank 1 Circuit Open Open or short in all fuel injector assembly circuits for 60 times or more (1 trip detection logic).
·

Open or short in fuel injector assembly circuit

·

Fuel injector assembly

·

D INJ relay

·

ECM


Comes on DTC stored SAE Code:
P062D

MONITOR DESCRIPTION

The fuel injection sequence occurs in numerical order from No. 1 to No. 4.

The ECM monitors the Injector Driver (EDU) at all times. If a driver or fuel injector assembly is malfunctioning, the EDU sends a fuel injector assembly operation condition signal (fail signal) to the ECM. When the ECM receives this signal, it stops the fuel injection control of the appropriate cylinder, cuts voltage to the appropriate D INJ relay, and illuminates the MIL.

MONITOR STRATEGY

Required Sensors/Components Fuel injector assembly
ECM (injector driver)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and warm it up.

9.

Idle the engine for 15 seconds or more.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read the DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P020113, P020213, P020313, P020413 or P062D13.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A384824E05
0.656,7.854 1.854,8.115 1.198,0.26 10 false Battery 1.333,8.417 2.188,8.625 0.854,0.208 10 false *3: Shielded 4.813,8.094 5,8.323 0.188,0.229 10 false *3 4.833,6.958 4.99,7.156 0.156,0.198 10 false *3 4.833,5.917 5.021,6.156 0.188,0.24 10 false *3 4.823,4.802 5.01,5.042 0.188,0.24 10 false *3 4.813,3.646 5,3.885 0.188,0.24 10 false *3 5.01,1.188 5.198,1.427 0.188,0.24 10 false *3 6,0.49 6.615,0.688 0.615,0.198 10 false +BD1 6,0.927 6.615,1.125 0.615,0.198 10 false +BD2 6.021,1.385 6.635,1.583 0.615,0.198 10 false IREL 6.021,1.844 6.635,2.042 0.615,0.198 10 false MREL 6.031,2.927 6.646,3.125 0.615,0.198 10 false #1D+ 6.052,3.344 6.667,3.542 0.615,0.198 10 false #1D- 6.031,4.063 6.646,4.26 0.615,0.198 10 false #2D+ 6.031,4.448 6.646,4.646 0.615,0.198 10 false #2D- 6.021,5.167 6.635,5.365 0.615,0.198 10 false #3D+ 6.021,5.573 6.635,5.771 0.615,0.198 10 false #3D- 6.031,6.24 6.646,6.438 0.615,0.198 10 false #4D+ 6.021,6.635 6.573,6.875 0.552,0.24 10 false #4D- 6.01,7.417 6.625,7.615 0.615,0.198 10 false E1D1 6.01,7.875 6.625,8.073 0.615,0.198 10 false E1D2 6.302,8.208 6.76,8.406 0.458,0.198 10 false ECM 1.594,3.698 4.229,3.927 2.635,0.229 10 false Fuel Injector Assembly (No. 1 Cylinder) 1.594,4.844 4.146,5.083 2.552,0.24 10 false Fuel Injector Assembly (No. 2 Cylinder) 1.51,5.99 4.25,6.24 2.74,0.25 10 false Fuel Injector Assembly (No. 3 Cylinder) 5.698,0.292 6.01,0.49 0.313,0.198 10 false 30 5.708,0.74 6.021,0.938 0.313,0.198 10 false 60 5.719,1.198 5.875,1.396 0.156,0.198 10 false 8 5.688,1.667 6,1.865 0.313,0.198 10 false 46 5.698,2.74 6.01,2.938 0.313,0.198 10 false 26 5.708,3.146 6.021,3.344 0.313,0.198 10 false 27 5.688,3.896 6,4.094 0.313,0.198 10 false 21 5.677,4.302 5.99,4.5 0.313,0.198 10 false 20 5.688,5 6,5.198 0.313,0.198 10 false 22 5.688,5.427 6.073,5.656 0.385,0.229 9 false 23 5.677,6.031 5.99,6.229 0.313,0.198 10 false 25 5.677,6.458 5.99,6.656 0.313,0.198 10 false 24 5.677,7.198 5.99,7.396 0.313,0.198 10 false 59 5.667,7.677 5.979,7.875 0.313,0.198 10 false 58 5.646,0.479 6.26,0.677 0.615,0.198 10 false C62 5.635,0.906 6.25,1.104 0.615,0.198 10 false C62 5.635,1.385 6.25,1.583 0.615,0.198 10 false A38 5.646,1.833 6.26,2.031 0.615,0.198 10 false A38 5.656,2.958 6.271,3.156 0.615,0.198 10 false C62 5.656,3.354 6.271,3.552 0.615,0.198 10 false C62 5.656,4.083 6.271,4.281 0.615,0.198 10 false C62 5.646,4.49 6.26,4.688 0.615,0.198 10 false C62 5.646,5.198 6.26,5.396 0.615,0.198 10 false C62 5.646,5.604 6.26,5.802 0.615,0.198 10 false C62 5.646,6.26 6.26,6.458 0.615,0.198 10 false C62 5.646,6.667 6.26,6.865 0.615,0.198 10 false C62 5.646,7.406 6.26,7.604 0.615,0.198 10 false C62 5.646,7.865 6.26,8.063 0.615,0.198 10 false C62 1.594,3.542 2.208,3.74 0.615,0.198 10 false X1 1.583,4.677 2.198,4.875 0.615,0.198 10 false X2 1.51,5.823 2.125,6.021 0.615,0.198 10 false X3 1.51,7.083 4.26,7.333 2.75,0.25 10 false Fuel Injector Assembly (No. 4 Cylinder) 1.521,6.917 2.135,7.115 0.615,0.198 10 false X4 0.448,6.969 1.448,7.167 1,0.198 10 false BATT MAIN 1.156,1.073 1.688,1.271 0.531,0.198 10 false D INJ 3.302,1.667 3.844,1.875 0.542,0.208 10 false D INJ 0.531,1.563 1.74,1.76 1.208,0.198 10 false EFI-MAIN NO. 1 2.01,2.156 2.792,2.354 0.781,0.198 10 false EFI-MAIN 3.823,1.281 4,1.5 0.177,0.219 11 false 1 3.083,1.292 3.24,1.49 0.156,0.198 10 false 2 3.823,0.813 3.979,1.01 0.156,0.198 10 false 3 3.083,0.813 3.24,1.01 0.156,0.198 10 false 5 1.906,1.302 2.063,1.5 0.156,0.198 10 false 3 2.656,1.302 2.813,1.5 0.156,0.198 10 false 4 2.646,1.75 2.896,1.979 0.25,0.229 10 false 5*2 2.646,1.594 2.917,1.792 0.271,0.198 10 false 6*1 1.771,2.469 2.24,2.688 0.469,0.219 10 false 1B 1.792,2.646 3.385,2.927 1.594,0.281 10 false No. 1 Integration Relay 1.333,7.583 3.938,7.781 2.604,0.198 10 false *1: for TMMT made 1.333,8 3.781,8.198 2.448,0.198 10 false *2: for TMC made 1.792,1.604 2.073,1.802 0.281,0.198 10 false 5*1 1.792,1.75 2.063,1.958 0.271,0.208 10 false 6*2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

If the current from the INJ relay is cut because DTC P062D13 is stored, DTC P123513 will be stored even if the fuel pump assembly (for high pressure side) is normal.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ DTC OUTPUT (DTC P020113, P020213, P020313, P020413 AND/OR P062D13)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Read the DTCs.

Result:
Result Proceed to
DTC P020113, P020213, P020313 or P020413 is output A
3 or more of the following DTCs are output: P020113, P020213, P020313 and P020413 B
P062D13 is output




A

2.CHECK HARNESS AND CONNECTOR (INSPECT FUEL INJECTOR ASSEMBLY)

B

4.INSPECT D INJ RELAY
2.CHECK HARNESS AND CONNECTOR (INSPECT FUEL INJECTOR ASSEMBLY)
a.

Disconnect the C62 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C62-26 (#1D+) - C62-27 (#1D-) 20°C (68°F) 1.74 to 2.04 Ω
C62-21 (#2D+) - C62-20 (#2D-) 20°C (68°F) 1.74 to 2.04 Ω
C62-22 (#3D+) - C62-23 (#3D-) 20°C (68°F) 1.74 to 2.04 Ω
C62-25 (#4D+) - C62-24 (#4D-) 20°C (68°F) 1.74 to 2.04 Ω
C62-26 (#1D+) or C62-27 (#1D-) - Body ground and other terminals Always 1 MΩ or higher
C62-21 (#2D+) or C62-20 (#2D-) - Body ground and other terminals Always 1 MΩ or higher
C62-22 (#3D+) or C62-23 (#3D-) - Body ground and other terminals Always 1 MΩ or higher
C62-25 (#4D+) or C62-24 (#4D-) - Body ground and other terminals Always 1 MΩ or higher


HINT:

The standard values shown are fuel injector assembly resistance values.



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT FUEL INJECTOR ASSEMBLY
3.INSPECT FUEL INJECTOR ASSEMBLY
a.

Check the resistance of the fuel injector assembly.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)

NG

REPLACE FUEL INJECTOR ASSEMBLY

4.INSPECT D INJ RELAY

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BATTERY - D INJ RELAY)

NG

REPLACE D INJ RELAY

5.CHECK HARNESS AND CONNECTOR (BATTERY - D INJ RELAY)
a.

Remove the D INJ relay from the No. 1 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (D INJ relay holder) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (D INJ RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (D INJ RELAY - ECM)
a.

Remove the D INJ relay from the No. 1 engine room relay block.


b.

Disconnect the A38 and C62 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (D INJ relay holder) - C62-30 (+BD1) Always Below 1 Ω
3 (D INJ relay holder) - C62-60 (+BD2) Always Below 1 Ω
1 (D INJ relay holder) - A38-8 (IREL) Always Below 1 Ω
3 (D INJ relay holder) or C62-30 (+BD1) - Body ground and other terminals Always 10 kΩ or higher
3 (D INJ relay holder) or C62-60 (+BD2) - Body ground and other terminals Always 10 kΩ or higher
1 (D INJ relay holder) or A38-8 (IREL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF D INJ RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF D INJ RELAY)
A384880C01
0.083,0.073 0.396,0.271 0.313,0.198 10 false *1 0.26,1.813 0.573,2.01 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 D INJ Relay Holder


a.

Remove the D INJ relay from the No. 1 engine room relay block.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
2 (D INJ relay holder) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

8.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - D INJ RELAY)
8.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - D INJ RELAY)
a.

Remove the D INJ relay from the No. 1 engine room relay block.


b.

Disconnect the 1B No. 1 integration relay connector.

HINT:

Remove the EFI-MAIN relay connected between the checked terminals as the coil inside the relay influences the measurement value.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-4 - 2 (D INJ relay holder) Always Below 1 Ω
1B-4 or 2 (D INJ relay holder) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR