Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › from 2019.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P023A12  Charge Air Cooler Coolant Pump Control Circuit Short to Battery  P023A13  Charge Air Cooler Coolant Pump Control Circuit Open  P023A14  Charge Air Cooler Coolant Pump Control Circuit Short to Ground or Open  


DESCRIPTION

The turbocharger and intercooler cooling system is a water cooling system that is independent from the engine cooling system. It uses a dedicated radiator and electric water pump assembly to cool the intercooler and turbocharger. The electric water pump assembly uses duty cycle signals sent from the ECM to provide stepless, optimal control of the electric water pump assembly speed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P023A12 Charge Air Cooler Coolant Pump Control Circuit Short to Battery Electric water pump assembly output voltage is specified value or higher (1 trip detection logic).
·

Open or short in electric water pump assembly circuit

·

Electric water pump assembly

·

ECM


Does not come on DTC stored SAE Code: P023C
P023A13 Charge Air Cooler Coolant Pump Control Circuit Open Electric water pump assembly speed is less than 10 rpm (1 trip detection logic).
·

Open or short in electric water pump assembly circuit

·

Electric water pump assembly

·

EFI-MAIN NO. 2 relay

·

ECM


Does not come on DTC stored SAE Code: P023A
P023A14 Charge Air Cooler Coolant Pump Control Circuit Short to Ground or Open Electric water pump assembly output voltage is specified value or less (1 trip detection logic).
·

Open or short in electric water pump assembly circuit

·

Electric water pump assembly

·

EFI-MAIN NO. 2 relay

·

ECM


Does not come on DTC stored SAE Code: P023B

MONITOR DESCRIPTION

If the electric water pump assembly operates at less than 10 rpm, the ECM determines there is a malfunction and stores DTC P023A13.

The electric water pump assembly operates steplessly according to duty cycle signals from the ECM. The ECM monitors the current operation speed of the electric water pump assembly. When the actual drive duty cycle ratio deviates from the target drive duty cycle, the ECM determines there is a malfunction and stores DTC P023A12 or P023A14.

CONFIRMATION DRIVING PATTERN

A330723E20
3.042,1.854 2.635,1.344 2.635,1.344 2.438,1.344 false 0.25,0.292 1.354,0.542 1.104,0.25 10 false Vehicle Speed 0.198,0.677 2.021,1.094 1.823,0.417 10 false 50 km/h (31 mph) 0.927,2.042 1.542,2.24 0.615,0.198 10 false Idling 0.396,2.365 1.313,2.75 0.917,0.385 10 false Ignition Switch ON 5.625,3.375 5.99,3.625 0.365,0.25 10 false [C] 1.427,1.26 2.729,1.563 1.302,0.302 10 false Fully depressed 2.198,1.885 2.656,2.083 0.458,0.198 10 false [A] 3.313,1.219 3.792,1.417 0.479,0.198 10 false [B]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

9.

Accelerate to 50 km/h (31 mph) or more with the accelerator pedal fully depressed [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P023A12, P023A13 or P023A14.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again.




WIRING DIAGRAM

A384825E06
0.698,4.5 1.771,4.698 1.073,0.198 10 false Battery 4.031,1.094 4.344,1.292 0.313,0.198 10 false +B 4.042,2.302 4.49,2.49 0.448,0.188 10 false PGND 4.823,1.094 5.219,1.281 0.396,0.188 10 false SWP 6.063,2.198 6.51,2.448 0.448,0.25 10 false IWPI 6.052,3.469 6.521,3.656 0.469,0.188 10 false MREL 6.052,0.99 6.583,1.177 0.531,0.188 10 false IWPO 6.271,4.771 6.688,4.969 0.417,0.198 10 false ECM 4.833,2.302 5.229,2.49 0.396,0.188 10 false NWP 5.823,0.969 6.25,1.177 0.427,0.208 10 false 24 5.813,2.177 6.24,2.385 0.427,0.208 10 false 11 5.813,3.458 6.24,3.667 0.427,0.208 10 false 46 6.281,4.594 6.708,4.802 0.427,0.208 10 false A38 5.25,0.99 5.677,1.198 0.427,0.208 10 false 3 5.25,2.188 5.677,2.396 0.427,0.208 10 false 2 3.854,0.99 4.281,1.198 0.427,0.208 10 false 4 3.854,2.188 4.281,2.396 0.427,0.208 10 false 1 0.51,3.448 1.49,3.646 0.979,0.198 10 false BATT MAIN 0.708,1.26 1.802,1.448 1.094,0.188 10 false EFI-MAIN NO. 2 0.698,2.979 1.906,3.229 1.208,0.25 10 false EFI-MAIN NO. 1 2.229,4.333 2.729,4.552 0.5,0.219 10 false 1B 2.49,3.906 3.25,4.104 0.76,0.198 10 false EFI-MAIN 1.917,1.708 3.073,1.958 1.156,0.25 10 false EFI-MAIN NO. 2 2.625,1.281 2.781,1.479 0.156,0.198 10 false 1 1.885,1.271 2.042,1.469 0.156,0.198 10 false 2 2.167,3.198 2.323,3.396 0.156,0.198 10 false 3 3.344,3.479 3.938,3.688 0.594,0.208 10 false 6*1, 5*2 2.625,0.99 2.781,1.188 0.156,0.198 10 false 3 3.344,3.198 3.5,3.396 0.156,0.198 10 false 4 1.885,0.979 2.042,1.177 0.156,0.198 10 false 5 1.74,3.479 2.427,3.688 0.688,0.208 10 false 5*1, 6*2 2.25,4.51 4.115,4.802 1.865,0.292 10 false No. 1 Integration Relay 4.01,2.667 4.51,2.885 0.5,0.219 10 false A56 4.021,2.844 5.333,3.354 1.313,0.51 10 false Electric Water Pump Assembly 1.573,5.052 4.177,5.25 2.604,0.198 10 false *1: for TMMT made 1.573,5.344 4.021,5.542 2.448,0.198 10 false *2: for TMC made

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTERCOOLER WATER PUMP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Intercooler Water Pump.

Powertrain > Engine > Active Test
Tester Display
Control the Intercooler Water Pump
50004 372 9

e.

According to the display on the GTS, perform the Active Test and check that the electric water pump assembly operates.

OK:

The electric water pump assembly is operating (vibrating).


HINT:

Use a sound scope if the operation is difficult to check.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - ECM)

NG

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ELECTRIC WATER PUMP ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - ECM)
a.

Disconnect the A56 electric water pump assembly connector.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A56-2 (NWP) - A38-11 (IWPI) Always Below 1 Ω
A56-3 (SWP) - A38-24 (IWPO) Always Below 1 Ω
A56-2 (NWP) or A38-11 (IWPI) - Body ground and other terminals Always 10 kΩ or higher
A56-3 (SWP) or A38-24 (IWPO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (IWPI VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TERMINAL VOLTAGE (IWPI VOLTAGE)
A347474C35
0.24,1.927 0.667,2.229 0.427,0.302 1.073,2.823 1.5,2.292 true 0.333,2 0.792,2.198 0.458,0.198 10 false A56 0.885,2.865 1.344,3.063 0.458,0.198 10 false NWP 0.24,0.219 0.552,0.417 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Electric Water Pump Assembly)


a.

Disconnect the electric water pump assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A56-2 (NWP) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRIC WATER PUMP ASSEMBLY

NG

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ELECTRIC WATER PUMP ASSEMBLY)
A347474C36
0.302,1.938 0.708,2.188 0.406,0.25 2.417,2.771 2.167,2.302 true 0.385,1.99 0.844,2.188 0.458,0.198 10 false A56 2.406,2.813 2.719,3.01 0.313,0.198 10 false +B 0.177,0.167 0.49,0.365 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Electric Water Pump Assembly)


a.

Disconnect the electric water pump assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A56-4 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - BODY GROUND)

NG

9.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - ELECTRIC WATER PUMP ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - BODY GROUND)
a.

Disconnect the A56 electric water pump assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A56-1 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - ECM)
a.

Disconnect the A56 electric water pump assembly connector.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A56-2 (NWP) - A38-11 (IWPI) Always Below 1 Ω
A56-3 (SWP) - A38-24 (IWPO) Always Below 1 Ω
A56-2 (NWP) or A38-11 (IWPI) - Body ground and other terminals Always 10 kΩ or higher
A56-3 (SWP) or A38-24 (IWPO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE ELECTRIC WATER PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE ELECTRIC WATER PUMP ASSEMBLY
a.

Replace the electric water pump assembly.

Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>WATER PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P023A12, P023A13 OR P023A14)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P023A12, P023A13 OR P023A14)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine and warm it up.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

j.

Input the DTC: P023A12, P023A13 or P023A14.


k.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P023A12, P023A13 or P023A14 is output)
B




A

END

B

9.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - ELECTRIC WATER PUMP ASSEMBLY)
a.

Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block.


b.

Disconnect the A56 electric water pump assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (EFI-MAIN NO. 2 relay holder) - A56-4 (+B) Always Below 1 Ω
3 (EFI-MAIN NO. 2 relay holder) or A56-4 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT EFI-MAIN NO. 2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT EFI-MAIN NO. 2 RELAY

Result:
Proceed to
OK
NG



OK

11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 2 RELAY)

NG

REPLACE EFI-MAIN NO. 2 RELAY

11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 2 RELAY)
a.
A384860C01
0.125,0.073 0.438,0.271 0.313,0.198 10 false *1 0.24,1.573 0.552,1.771 0.313,0.198 10 false *2
*1 No.1 Engine Room Relay Block
*2 EFI-MAIN NO. 2 Relay Holder


Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 2 relay holder) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 2 RELAY)

12.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)
a.
A384860C01
0.125,0.073 0.438,0.271 0.313,0.198 10 false *1 0.24,1.573 0.552,1.771 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 EFI-MAIN NO. 2 Relay Holder


Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EFI-MAIN NO. 2 relay holder) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - EFI-MAIN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - EFI-MAIN NO. 2 RELAY)
a.

Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block.


b.

Disconnect the 1B No. 1 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-4 - 1 (EFI-MAIN NO. 2 relay holder) Always Below 1 Ω
1B-4 or 1 (EFI-MAIN NO. 2 relay holder) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR