Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2019.09–2020.08
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0297889 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P163181  Communication Error from ECM to VSC Invalid Serial Data Received  


DESCRIPTION

The ECM sends signals such as A/T information signals, dynamic radar cruise control operation signals, brake operation demand signals, and buzzer operation demand signals to the skid control ECU (brake actuator assembly) when the dynamic radar cruise control is operating. Therefore, if the skid control ECU (brake actuator assembly) detects a communication error with the ECM, it sends a malfunction signal back to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area
P163181 Communication Error from ECM to VSC Invalid Serial Data Received While the dynamic radar cruise control system is operating, the ECM receives a logic fault signal from the skid control ECU (brake actuator assembly) for 1.0 second or more.
·

CAN communication circuit

·

ECM

·

Skid control ECU (brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the ECM refer to Service Bulletin.

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication system DTCs are not output OK
CAN communication system DTCs are output NG



OK

2.CHECK FOR DTCs (CRUISE CONTROL)

NG

2.CHECK FOR DTCs (CRUISE CONTROL)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Clear DTCs
50002 374

b.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.

1.

Turn the ignition switch to ON.

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF button).




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Trouble Codes
50001 374

Result:
Result Proceed to
DTC P163181 is not output A
DTC P163181 is output B



A

B

3.REPLACE ECM
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (CRUISE CONTROL)
4.CHECK FOR DTCs (CRUISE CONTROL)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Clear DTCs
50002 374

b.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.

1.

Turn the ignition switch to ON.

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF button).




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Trouble Codes
50001 374

Result:
Result Proceed to
DTC P163181 is not output A
DTC P163181 is output (for LHD) B
DTC P163181 is output (for RHD) C



A

END

B

C