Home › Engine / Hybrid System › 8NR-FTS (FUEL) › FUEL PUMP (for High Pressure) › from 2020.08
RM32H0E _51 Engine / Hybrid System _059909 8NR-FTS FUEL _0293898 FUEL PUMP(for High Pressure) A

8NR-FTS FUEL  FUEL PUMP(for High Pressure)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)
Replacement of fuel pump assembly (for high pressure) Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 4.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55737B 5.REMOVE HEATER AIR DUCT SPLASH SHIELD SEAL NO.1

Hide 55735A 6.REMOVE WATER GUARD PLATE LH (for TMC Made RHD)

Hide 55736D 7.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735C 8.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

Hide 55701J 9.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 10.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 53141F 11.REMOVE RADIATOR COVER

Hide 17751 12.REMOVE NO. 1 AIR CLEANER INLET

Hide 17705 13.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 23901 15.DISCONNECT FUEL TUBE SUB-ASSEMBLY

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


a.

Disconnect the fuel tube sub-assembly from the fuel pump assembly.

i.
A350924C02
0.948,3.083 1.219,3.083 false 2.354,4.333 2.354,4.063 false 1.854,4.167 1.854,3.896 false 2.406,3.51 2.573,3.146 2.573,3.146 2.677,3.146 true 2.479,3.844 2.708,4.344 2.708,4.344 2.792,4.344 false 1.708,4.167 2.01,4.167 2.01,4.167 2.01,3.896 false 2.74,3.073 3.052,3.229 0.313,0.156 10 false *a 2.271,4.375 2.583,4.531 0.313,0.156 10 false *b 0.771,3.01 1.083,3.167 0.313,0.156 10 false *c 1.51,4.094 1.823,4.25 0.313,0.156 10 false *d 2.865,4.281 3.177,4.438 0.313,0.156 10 false *e
*a Retainer
*b Fuel Tube Connector
*c Nylon Tube
*d O-ring
*e Fuel Pipe
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the fuel tube connector.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




iii.

Disengage the clamp to disconnect the fuel tube sub-assembly.


iv.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


v.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



Hide 23801P 16.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A350916C02
0,0 0,0 false
V100135

Union Nut
V100136

Bolt


Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.


b.

Remove the bolt.


c.
A350918N01
0.698,1.219 0.823,1.375 0.125,0.156 10 true A 2.375,1.438 2.5,1.594 0.125,0.156 10 true A 1.76,0.031 1.885,0.188 0.125,0.156 10 true B

Loosen the 2 bolts (A).


d.

Remove the bolt (B).


e.

Remove the No. 1 fuel pipe sub-assembly from the fuel delivery pipe and fuel pump assembly.


Hide 23100X 17.REMOVE FUEL PUMP ASSEMBLY

a.
A350919

Disconnect the fuel pump assembly connector.


b.
A350920

Remove the 2 bolts, fuel pump assembly and fuel pump protector from the cylinder head cover sub-assembly.


c.
A350921C03
0.594,1.104 0.958,1.104 false 1.073,2.5 1.438,2.5 false 0.646,3.656 1.01,3.656 false 0.427,1.021 0.74,1.177 0.313,0.156 10 false *1 0.896,2.406 1.208,2.563 0.313,0.156 10 false *2 0.479,3.573 0.792,3.729 0.313,0.156 10 false *3
*1 Fuel Pump Assembly
*2 Fuel Pump Lifter Assembly
*3 Fuel Pump Lifter Guide


Remove the fuel pump lifter guide and fuel pump lifter assembly from the fuel pump assembly.


d.
A344047

Remove the O-ring from the fuel pump assembly.


e.
A350922C02
1.635,1.802 1.635,1.552 true 0.875,0.385 1.021,0.385 1.021,0.385 1.125,0.875 true 2.74,1.229 2.354,1.229 true 1.552,1.833 1.74,2.01 0.188,0.177 10 true *1 2.781,1.167 2.958,1.323 0.177,0.156 10 true *2 0.667,0.313 0.844,0.469 0.177,0.156 10 true *2
*1 Fuel Pump Spacer Gasket
*2 O-ring


Remove the fuel pump spacer gasket from the cylinder head cover sub-assembly.


f.

Remove the 2 O-rings from the No. 4 camshaft bearing cap.