The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump removal/installation are shown below.
Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2. DISCHARGE FUEL SYSTEM PRESSURE
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
4.REMOVE REAR SEAT ASSEMBLY
58325E
5.REMOVE REAR FLOOR SERVICE HOLE COVER LH
| *a | Protective Tape |
Using a clip remover with its tip wrapped with protective tape, remove the rear floor service hole cover LH and butyl tape.
Disconnect the fuel suction tube with pump and gauge assembly connector.
6.DISCONNECT FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY
Disconnect the fuel tank evaporation vent tube sub-assembly from the fuel suction tube with pump and gauge assembly.
Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>PRECAUTION
77209F
7.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
| *1 | Fuel Suction Plate Sub-assembly |
| *2 | Tube Joint Clip |
| *3 | Fuel Tank Main Tube Sub-assembly |
| *a | Fuel Tube Joint |
| *b | O-ring |
| *c | Nylon Tube |
|
Pull off |
|
Pull off |
Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.
Remove any foreign matter on the fuel tube joint before performing this work.
Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).
Be sure to disconnect the fuel tube joint by hand.
Do not bend, twist, pinch or kink the nylon tube.
Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.
If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.
77026A
8.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
Slide the clip and disconnect the No. 1 fuel evaporation tube sub-assembly from the fuel suction tube with pump and gauge assembly.
77754B
9.DISCONNECT CHARCOAL CANISTER OUTLET HOSE
Slide the clip and disconnect the charcoal canister outlet hose from the fuel suction tube with pump and gauge assembly.
77144
10.REMOVE FUEL PUMP GAUGE RETAINER
|
Front Side of Vehicle |
Disengage the claw to remove the No. 1 fuel tube clamp.
Remove the fuel pump gauge retainer.
| *a | Insertion Point |
| *b | SST (Plate) |
| *c | SST (Claw) |
| *d | SST (Bolt) |
Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.
Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.
While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).
| *a | SST (Handle) |
| *b | SST (Plate) |
| *c | SST (Claw) |
| *d | SST (Bolt) |
Install SST (handle) to SST (plate).
Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.
Do not use any tools other than specified in this operation as this may result in damage to the fuel pump gauge retainer or the fuel tank assembly.
Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.
Do not spin SST too fast or use an impact wrench as this may result in damage to components.
If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.
While pressing down on the fuel suction tube with pump and gauge assembly, remove the fuel pump gauge retainer.
77020A
11.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
Disconnect the fuel return vent tube sub-assembly and remove the fuel suction tube with pump and gauge assembly from the fuel tank assembly.
Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>PRECAUTION
Be careful not to bend the arm of the fuel sender gauge assembly.
Remove the fuel suction tube set gasket from the fuel tank assembly.